Pacific Scientific 6430 Installation & Hardware Reference Manual Download Page 23

Page: 23 / 60

J3 connection

table

Output

Pin

Explanation

Motor Phase A J3-1

Motor Phase A excitation. Twisted

Pair.

Motor Phase A J3-2

Motor Phase B J3-3

Motor Phase B excitation. Twisted

Pair.

Motor Phase B J3-4

Drive Case

(Earth) Ground

J3-5

Connected to the motor case

ground.

Mating

connector

The J3 motor connector on the 6430 mates to a 5-pin PCD

screw cable connector. The mating cable connector is type

ELVP05100.

Cable

requirements

The mating connector terminals will accept #16 to #18 AWG

wire. Pacific Scientific recommends using #16 AWG.
For the motor cable, use cable with two twisted pairs twisted at

about 3 to 4 turns per inch (1 to 1.5 turns per centimeter) for

the motor phase excitations and a fifth wire for the case

ground. As an option, the cable may be shielded to reduce

radiated noise. A single shield can be used around both phase

excitations and the ground wire or each phase excitation

(twisted pair) can be individually shielded as in the Pacific

Scientific cables. Connect shields to pin 5 of the mating

connector.

2 - 10

6430 Installation and Hardware Reference Manual - Rev 1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 6430





























































Search results

Summary of Contents for 6430

Reviews:

Related manuals for 6430

Brands by name

Popular brands

Pacific Scientific 6430, Installation & Hardware Reference Manual

Search results

Summary of Contents for 6430

Reviews:

Related manuals for 6430

Brands by name

Popular brands