Pacific Scientific 6430 Installation & Hardware Reference Manual Download Page 44 | Manualshive

Page: 44 / 60

background image

4 Maintaining/Troubleshooting

In this chapter

This chapter covers maintenance and troubleshooting of the

6430 unit.

4.1 Maintaining the 6430 Drive

Introduction

The 6430 drives are designed for minimum maintenance. The

following cleaning procedure, performed as needed, will

minimize problems due to dust and dirt build-up.

Procedure

Remove superficial dust and dirt from the unit using clean,

dry, low-pressure air.

4.2 Troubleshooting the 6430 Drive

Introduction

The 6430 has an “enabled” output which is on when the drive

is enabled and off when the drive is disabled or faulted due to

any of the following:

•

Output overcurrent (line-to-line or line-to-neutral short)

•

Bus overvoltage

•

Low voltage supply out of tolerance.

Procedure

Use the troubleshooting tables and the simple circuit shown on

the following pages to diagnose and correct most problems. If

you are unable to achieve satisfactory operation, contact your

local Pacific Scientific Distributor or the Applications

Engineering Department.

6430 Installation and Hardware Reference Manual - Rev 1

4 - 1

Powering

Up

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
42
43
44
45
46
...
»

Summary of Contents for 6430





























































Reviews:

No comments

Related manuals for 6430

Brand: ABB Pages: 334

Brand: Ltech Pages: 7

Brand: YASKAWA Pages: 114

ADV200-SI Series

Brand: gefran Pages: 14

Brand: Siemens Pages: 10

SINAMICS V20 Inverter

Brand: Siemens Pages: 28

Brand: Siemens Pages: 122

Brand: Siemens Pages: 132

SINAMICS SM150 6SL3815-7NP41-0AA1

Brand: Siemens Pages: 198

Brand: Siemens Pages: 218

SINAMICS V20 Inverter

Brand: Siemens Pages: 426

SINAMICS V20 Series

Brand: Siemens Pages: 274

Brand: Hafele Pages: 84

Brand: Delta Pages: 815

Brand: Targus Pages: 28

Brand: YASKAWA Pages: 502

Brand: Dover Pages: 26

Brand: Malmbergs Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands