background image

Page 21

SKU 95156

For technical questions, please call 1-800-444-3353.

Emission control System Warranty

california and United States Emission control defects Warranty Statement

The California Air Resources Board (herein CARB), the United States Environmental Protection Agency (herein EPA), and Harbor Freight 

Tools

®

 (herein HFT) are pleased to explain the emission control system warranty on your 1995 and later Small Off-Road Engine (herein 

engine). In California, the engine must be designed, built and equipped to meet the State’s stringent anti-smog standards.  Elsewhere 

within the United States, new off-road, spark-ignition engines certified for model year 1997 and later, must meet similar standards set 

forth by the EPA.  HFT must warrant the emission control system on your engine for the periods of time described below, provided 

there has been no abuse, neglect or improper maintenance of your engine.
Your emission control system may include parts such as the carburetor or fuel-injection system, and the ignition system. Also included 

may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, HFT will repair your engine at no cost to you including diagnosis, parts and labor.

Manufacturer’s Warranty coverage

The 1995 and later engines are warranted for two (2) years.  If any emission-related part on your engine is defective, the part will be 
repaired or replaced by HFT.

Harbor Freight tools Emission control defects Warranty coverage

Engines are warranted for a period of two (2) years relative to emission control parts defects, subject to the provisions set forth below. 
If any emission related part on your engine is defective, the part will be repaired or replaced by HFT.

Owner’s Warranty Responsibilities

-  As the engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. HFT 

recommends that you retain all receipts covering maintenance on your engine, but HFT cannot deny warranty solely for the lack 

of receipts or for your failure to ensure the performance of all scheduled maintenance.

-  As the engine owner, you should, however, be aware that HFT may deny you warranty coverage if your engine or a part has failed 

due to abuse, neglect, improper maintenance, or unapproved modifications.

-  You are responsible for shipping your engine to a HFT warranty station as soon as a problem exists.  Contact the HFT Customer 

Service department at the number below to make shipping arrangements.  The warranty repairs should be completed in a reason-

able amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact the Harbor Freight Tools Customer 

Service Department at 1-800-444-3353.

Harbor Freight tools Emission control defects Warranty Provisions

1.  length of coverage

HFT warrants to a first retail purchaser and each subsequent purchaser that the engine is free from defects in materials and 

workmanship that cause the failure of warranted parts for a period of two (2) years after the date of delivery to the first retail 

purchaser.

2.  no charge Repair or Replacement

Repair or replacement of any warranted part will be performed at no charge to the owner if the work is performed through a warranty 
station authorized by HFT.  For emissions warranty service, contact the HFT Customer Service Department at 1-800-444-3353.

3.  consequential damages coverage

Coverage under this warranty shall also extend to the failure of any engine components caused by the failure of any warranted 
part while it is still covered under this warranty.

4.  coverage Exclusions

Warranty claims shall be filed in accordance with the provisions of the HFT warranty policy explained in the box at the top of the 

previous page.  HFT shall not be liable for any loss of use of the engine, for any alternative usage, for any damage to goods, loss 

of time, or inconvenience.  Warranty coverage shall also be excluded for any part which fails, malfunctions, or is damaged due to 

failure to follow the maintenance and operating instructions set forth in the Owner’s Manual including, but not limited to:
(a)  use of parts which are not authorized by HFT
(b)  improper installation, adjustment or repair of the engine or of any warranted part unless performed by an authorized warranty 

center

(c)  failure to follow recommendations on fuel use contained in the Owner’s Manual
(d)  improper or inadequate maintenance of any warranted parts
(e)  repairs performed outside of the authorized warranty service dealers
(f)  alterations by changing, adding to or removing parts from the engine.

Summary of Contents for 95156
























Reviews: