background image

GAS PRESSURE WASHER

2.5 HP - 1300 PSI

Model

95156

ASSEMbly And OPERAtInG InStRUctIOnS

cAUtIOn

your warranty is voided if you do not put engine oil in the Engine’s crankcase 

prior to its first use.

Before each use, check the oil level.  Never run the Engine with low or no engine oil.

Running the Engine with low or no oil will permanently damage the unit.

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

distributed exclusively by Harbor Freight tools

®

.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

 Read this material before using this product.  

Failure to do so can result in serious injury. 

SAVE tHIS MAnUAl.

Copyright

©

 2007 by Harbor Freight Tools

®

.  All rights reserved.  No portion of this 

manual or any artwork contained herein may be reproduced in any shape or form 

without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

cover Revised 07h

Summary of Contents for 95156
























Reviews: