13
300309-20
Maintenance
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value.
This is why hardwoods are generally preferred. Green
or wet wood will cause a rapid buildup of creosote. If you
feel it is necessary to burn wet or unseasoned wood, do
so only with the air inlet set open enough to maintain a
good strong fire and fairly high chimney temperatures.
Do not attempt to burn overnight using green or wet
wood. Wet wood can cause up to 25% drop in heater
output, as well as contributing significantly to creosote
buildup.
WARNING: Never use chemicals or any other volatile
liquid to start a fire. Do not burn garbage, or flammable
fluids such a gasoline, naptha, or engine oil. We strongly
recommend that smoke detectors be installed.
2. Remove ashes frequently. Embers can roll out the door
and create a fire hazard. Maintain a 1" minimum ash
base.
3. If glass becomes darkened through slow burning or poor
wood, it can readily be cleaned with any fireplace glass
cleaner when stove is cold. Never scrape with an object
that might scratch the glass. The type and amount of
deposit on the glass is a good indication of flue pipe
and chimney buildup. A light brown dusty deposit that
is easily wiped off usually indicates good combustion
and dry, well-seasoned wood and therefore relatively
clean pipes and chimney. On the other hand, a black,
greasy deposit that is difficult to remove is a result of
wet and green wood and too slow a burning rate. This
heavy deposit is building up at least as quickly in the
chimney.
WARNING: Only use materials supplied by the manu-
facturer when doing maintenance or replacements.
4. DOOR GASKET - The gasket used by Pacific Energy
requires only light pressure to seal. This will prolong seal
life. It is important that the door seal be maintained in
good condition. Periodically inspect seals and replace
if necessary. Follow instructions included in the Service
Kit (SVCK.10178) obtainable from your nearest Pacific
Energy Dealer.
5. DOOR GLASS - Do not slam loading door or otherwise
impact glass. When closing door, make sure that no logs
protrude to impact the glass. If the glass gets cracked
or broken, it must be replaced before using the stove.
Replacement glass can be obtained from your Dealer.
The size required is 9-1/8 x 15-5/8 x 5 mm Robax. Ce-
ramic glass must be used. Do not substitute with any
other type.
To remove broken glass, undo the four retaining screws
and remove the frame noting position for re-assembly.
Remove all particles of glass. Be careful as they are very
sharp. Install new glass complete with gasket. Replace
frame and screws.
WARNING: Do not overtighten, tighten screws very
carefully.
- Do not clean glass when hot
- Do not use abrasive cleaners on glass
6. The area where boost combustion air enters the firebox
must be kept clear of excessive ash buildup which will
block air flow. This area is at the front of the firebox.
7. Do not store wood within heater installation clearances,
or within the space required for fuel loading and ash
removal. Keep the area around the heater clean and
free of all loose combustibles, furniture, newspapers,
etc.
8. If plated door requires cleaning, use mild soap and water
only. Use of abrasive cleaners will void warranty.
9. Establish a routine for the fuel, wood burning and firing
technique. Check daily for creosote buildup until experi-
ence shows how often you need to be cleaning to be
safe.
10. Be aware that the hotter the fire, the less creosote is
deposited. Weekly cleaning may be necessary in mild
weather, even though monthly cleaning is usually enough
in the coldest months when burning rates are higher.
11. Instruct all members of your family on the safe operation
of the heater. Ensure they have enough knowledge
of the entire system if they are expected to operate it.
Stress the section on chimney fires and the importance
of following the steps outlined in “In Case of Chimney
Fire”.
Baffle Removal
The Insert and pipe should be removed from the fireplace
to clean and inspect. Only if this is not possible should you
remove baffle assembly.
DO NOT OPERATE WITH BAFFLE ASSEMBLY OR IN-
SULATION REMOVED.
Baffle Assembly Removal
Remove retaining pin at the back top of the firebox, just
under the baffle. Lift baffle up and pull forward to disconnect
from the supply tube. Tilt baffle sideways to drop down and
remove from firebox.
Inspect gasket between baffle and supply tube. If necessary,
replace with gasket # 139.5 available from your nearest
Pacific Energy Dealer.
Re-install baffle assembly and insulation by reversing
order.
Summary of Contents for Pacific Wood Insert DESIGN-D
Page 17: ...17 300309 20 NOTES...
Page 18: ...18 300309 20 NOTES...
Page 19: ...19 300309 20 Label...
