background image

Changing the direction of rotation 

The direction of rotation can be changed with the
forward/reverse selector (3). This is located above
the variable speed trigger switch (2) (Fig. 13). 

To select the forward driving or tightening position,
push the forward/reverse selector (3) hard left. 

To select the reverse driving or loosening position
push the forward/reverse selector (3) hard right. 

The variable speed trigger switch (2) can be locked off by pushing the
forward/reverse selector (3) into the middle of both forward and reverse
positions. 

WARNIING!

Do not change direction of rotation unless the tool has

come to a complete stop.

Using the tool

Insert the correct driving bit or socket bit (with socket adaptor).

Before starting your job, always perform a test operation in a scrap piece of
material. 

When fastening screws sized M8 or smaller, take particular care to use light
pressure on the variable speed trigger switch (2) for fear of damaging the fixture.

Hold the tool pointing straight in line with the fastener
and apply sufficient forward pressure to stop the bit
from slipping off the fastener (Fig. 14).

Apply slight pressure to the variable speed trigger
switch (2) to turn on the tool then increase the speed
according to the circumstances.

Do not apply torque for too long when tightening a
screw or nut or it will be damaged.

Note: 

The correct fastening or loosening torque will vary according to the size and

type of fastener, the material in which the fastener is inserted and the state of the
battery charge.

Note: 

The tool has a “sleep” mode that helps to extend the run time of the

battery (6). After a period of non-use, the tool will hesitate slightly before starting.
This indicates that the battery (6) is coming out of “sleep” mode and is normal.

IMPACT DRIVER OPERATION (cont.)

15

Fig. 14

Fig. 13

!!

 

 

 

 

 

 

 

 

 

 

 

 

 

    

Summary of Contents for IDL-018





















Reviews: