Owon MSO7102T User Manual Download Page 98

Page: 98 / 117

User’s Manual of

OWON

Color Mixed Signal Digital Storage Oscilloscope

Demonstration

Example 1: Measurement of Simple Signals

Observe an unknown signal in the circuit, and display and measure rapidly the
frequency and peak-to-peak value of the signal.

1. Carry out the following operation steps for the rapid display of this signal:

Set the probe menu attenuation coefficient as

10X

and that of the switch in the

probe switch as

10X

Connect the probe of

Channel 1

to the measured point of the circuit.

Push down the

AUTOSET

button.

The oscilloscope will implement the

AUTOSET

to make the wave form optimized,

based on which, you can further regulate the vertical and horizontal divisions till the
waveform meets your requirement.

2. Perform Automatic Measurement

The oscilloscope can measure most displayed signals automatically. Complete the
following operations for the measurement of frequency, cycle, mean and peak-to-peak
value:

Press the

MEASURE

button to show the automatic measurement function menu.

Press the

menu selection button and choose

Source

, with the

Source

displayed.

Press the

F2, F3, F4

and

menu selection buttons and choose

CH1

Press the

menu selection button again and choose

Type,

with the

Type

displayed.

Press the

menu selection button and choose

Freq

Press the

menu selection button and choose

Period

Press the

menu selection button and choose

Mean

Press the

menu selection button and choose

Pk-Pk

Then, the frequency, cycle, mean and peak-to-peak value will present in the menu and
change periodically (see Fig. 90).

Summary of Contents for MSO7102T






















































































































Search results

Summary of Contents for MSO7102T

Reviews:

Related manuals for MSO7102T

Brands by name

Popular brands

Owon MSO7102T, User Manual

Search results

Summary of Contents for MSO7102T

Reviews:

Related manuals for MSO7102T

Brands by name

Popular brands