Owon MSO7102T User Manual Download Page 22

Page: 22 / 117

User’s Manual of

OWON

Color Mixed Signal Digital Storage Oscilloscope

Fig. 10

Horizontal Control Zone

Use the horizontal

“SEC/DIV”

knob to change the horizontal time base setting

and observe the consequent status information change. Rotate the horizontal
“

SEC/DIV

” knob to change the horizontal time base, and it can be found that the

“

Horizontal Time Base

” display in the status bar changes accordingly. The

horizontal scanning speed steps from 5ns up to 100s in the sequence of 1-2-5.

Use the “

HORIZONTAL POSITION

”

knob to adjust the horizontal position of

the signal in the waveform window. The “

HORIZONTAL POSITION

”

knob is

used to control the triggering displacement of the signal or for other special
applications. If it is applied to triggering the displacement, it can be observed that
the wave form moves horizontally with the knob when you rotate the
“

Horizontal

Position

” knob.

With the “

HORIZONTAL MENU

” button pushed down, you can set and

initiate the Window Expansion.

Introduction to the Trigger System

Shown as Fig.11, there are a knob and four buttons in the “

TRIGGER

CONTROLS

”. The following practices will direct you to be familiar with the setting

of the trigger system gradually.

Summary of Contents for MSO7102T






















































































































Search results

Summary of Contents for MSO7102T

Reviews:

Related manuals for MSO7102T

Brands by name

Popular brands

Owon MSO7102T, User Manual

Search results

Summary of Contents for MSO7102T

Reviews:

Related manuals for MSO7102T

Brands by name

Popular brands