Owon MSO7102T User Manual Download Page 7

Page: 7 / 117

User’s Manual of

OWON

Color Mixed Signal Digital Storage Oscilloscope

Please do not make any operates in an explosive environment.

Keep the products surface clean and dry.

Safety Terms and Symbols

Terms in this manual.

The following terms may appear in this manual:

Warning.

warning statement indicates the conditions and actions which may

endanger the life safety.

Note.

A note statement indicates the conditions and actions which may cause

damage to this product or other property.

Terms on the product.

The following terms may appear on this product:

Danger:

It indicates that there

may be an immediate injury to you when you encounter

this mark.

Warning:

indicates that there may not be an immediate injury to you when you

encounter this mark.

Note:

indicates that there may be damage to this product or other property.

Symbols on the product

. The following symbol may appear on the products:

High Voltage Please Consult the Manual. Protective Ground End Earth End on the Shell Grounding End for Measurement

Summary of Contents for MSO7102T






















































































































Search results

Summary of Contents for MSO7102T

Reviews:

Related manuals for MSO7102T

Brands by name

Popular brands

Owon MSO7102T, User Manual

Search results

Summary of Contents for MSO7102T

Reviews:

Related manuals for MSO7102T

Brands by name

Popular brands