Oursson EK1775MD, Instruction Manual

Page: 12 / 76

12
To accelerate the cooling of the heating
element, do not fill kettle with cold water. This
may damage the heating element.
When the kettle is in the “BOILING” mode, you
can turn it off by pressing the button again.
the base. Plug in. You will hear a sound and the display
will show the current temperature and the inscription
SET 60, indicating the default temperature of 60° C.
Kettle is in standby mode.
2. Press
button a few times to set the desired heating
temperature of the water. The minimum value of heating
is 60° C, maximum - 100° C. Every press of the button
changes the temperature for 10 ° C. If you exceed the
maximum heating temperature, it will returned to the
original settings - 60° C.
If you do not set additional options, after selecting the
desired temperature, in 3 seconds the kettle goes into a
heating mode.
Heating mode can be enabled immediately by pressing the
button.
During heating, the temperature mode indicator is flashing,
indicating that the water is heating.
During the heating process, you can change the tempera -
ture by pressing the button.
After heating the water to a predetermined temperature, the
kettle will automatically turn off and go into standby mode,
displaying the current temperature.
NOTE!
Set temperature should not be below the current
water temperature. If you immediately press the but -
ton in the standby mode, without setting a predetermined
temperature, the kettle will switches to heating water to 60° C
mode.
Heating water and keeping it at a predetermined
temperature:
Temperature maintain mode is implemented in two
versions:
• Heating water to the desired temperature with its further
maintenance.
• Boiling the water with subsequent cooling down to a
predetermined temperature and maintaining at this
level .
1. To activate, press the button, select the desired
temperature using the button.
2. ЕIf you do not set additional options, after selecting the
desired temperature, in 3 seconds the kettle goes into
a heating mode and will keep it at a set temperature. In
this mode, the kettle works for 2 hours.
3. When mode indicator is flashing, the water is heating.
When it is not flashing, water heating is stopped.
4. After two hours, if the mode has not been interrupted,
you will hear a sound and kettle will go into a standby
mode.
OPERATION ORDER:
Turning off the kettle
There are two ways of turning off the kettle:
• Push button, when the device is working;
• When the kettle is working, remove it from the stand.
The kettle is equipped with protection from
switch-on without water. If you turn on the kettle
with no water or less then MIN mark, the device
will turn off after a few seconds. After cooling
the heating element, the kettle will get back to
working condition. Clicking sounds made by the
kettle, indicate the reset of thermostat.
WARM-UP
button
LED
– display
Informational Display, Рiс. С-2
Temperature selection mode indication
“BOILING” mode indication
Device working mode indication
“WARM-UP” mode indication
Temperature indication
Temperature adjustment indication
The kettle is intended only for heating drinking water
for domestic purposes.
You can use the kettle in the following modes:
• Heating water to a predetermined temperature;
• Maintaining a certain water temperature for 2 hours;
• Boiling the water.
BEFORE FIRST USE:
• Wash the inner surface of your new kettle with the use
of non-abrasive cleaners. Dry the kettle. Wipe the kettle
with a clean dry cloth.
• Boil the maximum amount of water in a safe manner as
described in the previous section. Monitor for no leaks,
sparks, melting of body, stand, excessive heating of
the power cord, plug, and burning smell during first two
boiling.
• Boiled water from the first two boiling is not
recommended to use in food. You can use it for
everyday needs.
Boiling the water:
1. Remove the kettle from the base, open the lid by pressing
the button on the handle of the kettle, and fill it with water.
2. Close the lid and put the kettle on the base. Plug in. You
will hear a sound and the display will show the current
temperature and the inscription SET 60, indicating the
default temperature of 60° C. Kettle is in standby mode.
3. Click mode button to heat the water up to 100° C.
4. mode indicator will light up and the display will show
the current water temperature during heating.
5. After heating the water to 100° C, you will hear a sound and
the kettle will automatically turn off by going into standby
mode.
Heating water to a predetermined temperature:
1. Fill the kettle with water, close the lid and put the kettle on
Hard water can leave scale in the kettle. Use special
cleaners for descaling. Follow the instructions of the used
detergent. Do not use abrasive or harsh cleaners.
• Fill the kettle halfway with water.
• For every 2 cups of water, add 6 tablespoons of white
vinegar 8%.
• Bring to a boil.
• Repeat the procedure if necessary.
• Unplug it.
• Allow the kettle to cool and rinse it twice with cold water.
• Wipe the outside of the kettle with a clean, soft,
damp cloth. In order to prevent electrical shock do
not immerse the entire product or the wires into the
water.
• Thoroughly dry all the parts of the device.
CLEANING AND MAINTENANCE, Рiс. D