background image

18

Optional accessories

OULINK

Adapter for Ouflex M for networking 

OULINK is an Ouflex M adapter 

that is providing Modbus TCP/IP interface to Ouflex M

• 

Integrated Ouman Access connection

• 

Modbus TCP/IP

• 

Modbus TCP/IP 

 RTU Gateway

• 

SNMP alarm transfer

Additional Control panel, Ouflex C LCD

The external display is connected to the flap cover over the RJ12 jack. 
Use Ouman cable LCD CABLE M.

SIM card slot 

SIM card release button

Antenna 

attachment

GSMMOD5

By connecting the modem to the Ouflex M  you can communicate with 
SMS’s to the controller and have information of activated alarms to 
GSM phone.

Ouman’s GSM modem (GSMMOD5) is connected to the COM3 port 
(RJ45) of Ouflex M unit.  The modem has a fixed antenna that can 
be changed to an external antenna with a 2,5m cord (optional equip-
ment) if needed. The modem’s indicator light shows what mode it is in.

Led indicator light

Modem mode/instructions

LED is not lit:

Modem is not on. Connect network device to modem.

LED is lit:

Modem is on, but it is not ready for use. Make sure that Ouflex 

M and GSM modem SIM card have the same PIN code, if PIN in-

quiry is in use.

LED is blinking slowly:

Modem is ready for use.

LED is blinking rapidly: Modem is either sending or receiving a message. 

Inserting the SIM card

Press the small black SIM card release button with, for example, a pen 
tip. Part of the SIM card slot will stick out of the modem. Pull the slot 
out of the modem. Do not pull the slot out of the modem without pres-
sing the SIM card release button first!

Insert SIM card into the slot and make sure it settles properly. Push 
the slot back to its place. Set the SIM card PIN code as Ouflex M devi-
ce PIN code. Make sure PIN inquiry is in use in the SIM card.

Product disposal

The enclosed marking on the additional material of the product indicates that this product 
must not be disposed of together with household waste at the end of its life span. The pro-
duct must be processed separately from other waste to prevent damage caused by uncont-
rolled waste disposal to the environment and the health of fellow human beings. The users 
must contact the retailer responsible for having sold the product, the supplier or a local envi-
ronmental authority, who will provide additional information on safe recycling opportunities 
of the product. This product must not be disposed of together with other commercial waste.

RJ-45 connectori to the 
modem

8

7

6

5

D

C

B

A

B

C

D

E

F

1

2

3

4

5

6

7

8

F

E

A

Date

Pages

Author

Designer

Scale

Document type

Document description

Item

Document code and revision

1/1

Modifier

Page size

1:1

A4

XL740-A-01

Printing color: RAL 9005 Jet Black

Drawing

OUFLEXMINI PRINTED COVER

09.06.2015

MM

--

--

XL740

9 10

11 12

13 14

15 16

17 18

19 20

C NO

C NO

C NO

C NO

C NO

C NO

1 2

3 4 5

6 7 8

24V ~/+ 

B2 A2

B1 A1

21

22 32 42

25

62 72 82 29 03 13 23 33 43 53 63

37

83 93 04

41

24 34 44

45

64 74 84 49 05 15 25 53 45 55 65

57

85 95 06

Y1

PWM

Y3

2Y

M5

4Y

M4

M3

M2

M1

M14

51

M

M12

31

M

M10

M11

M9

M8

M7

M6

Print1)

Print2)

Print3)

Summary of Contents for Ouflex M





















Reviews: