Oracle Exadata Storage Server X7-2 EF Installation Manual Download Page 72

Page: 72 / 90

Back Cable Connections and Ports

Note -

To achieve 10 GbE network speeds, use Category 6 (or better) cables and network

devices that support 1000BASE-T networks.

The LEDs located above each NET port are Link/Activity (left) and Speed (right) indicators for

each port. The following table lists the Ethernet transfer rates and the Speed LED color.

Connection Type

IEEE Terminology

Speed LED Color

Transfer Rate

Fast Ethernet

100BASE-TX

Off

100 Mbits/sec

Gigabit Ethernet

1000BASE-T

Amber

1,000 Mbits/sec

10 Gigabit Ethernet

10GBASE-T

Green

10,000 Mbits/sec

Powering On the Oracle Exadata Rack

For instructions on how to power on the Oracle Exadata Rack, refer to the

Oracle Exadata

Database Machine Installation and Configuration Guide

https://docs.oracle.com/cd/

E80920_01/index.htm

Caution -

Do not connect the power cords to the storage server until you have made the service

processor (SP) and host networking cable connections. The storage server includes an SP that

you use to configure and boot the host system. Connecting the SP and host networking cables

first enables you to properly configure the host system and view SP messages.

Server Boot Process and Normal Operating State Indicators

A normal server boot process involves two indicators, the service processor SP OK LED

indicator and the System OK LED indicator.

When you connect AC power to the server, the server boots into standby power mode:

1. The SP OK LED blinks slowly (0.5 seconds on, 0.5 seconds off) while the SP is starting,

and the main System OK LED remains off until the SP is ready.

2. After a few minutes, the main System OK LED slowly flashes the standby blink pattern

(0.1 seconds on, 2.9 seconds off), indicating that the SP is ready for use. In Standby power

mode, the server is not initialized or fully powered on at this point.

When powering on the server (either by the On/Standby button or Oracle ILOM), the server

boots to Main power mode:

Oracle Exadata Storage Server X7-2 EF and HC Installation Guide • November 2018

Summary of Contents for Exadata Storage Server X7-2 EF



























































































Search results

Summary of Contents for Exadata Storage Server X7-2 EF

Reviews:

Related manuals for Exadata Storage Server X7-2 EF

Brands by name

Popular brands

Oracle Exadata Storage Server X7-2 EF, Installation Manual

Search results

Summary of Contents for Exadata Storage Server X7-2 EF

Reviews:

Related manuals for Exadata Storage Server X7-2 EF

Brands by name

Popular brands