Oracle Exadata Storage Server X7-2 EF Installation Manual Download Page 41

Page: 41 / 90

Install AC Power Cables and Slide-Rails

Place the Rackmounting Template against the front rails, aligning the bottom

edge of the card with the bottom edge of the storage server, and measure up

from the bottom of the Rackmounting Template.

Mark the mounting holes for the front slide-rails.

Mark the mounting holes for the back slide-rails.

Related Information

■

“Rack Compatibility” on page 36

■

“Install Mounting Brackets on the Server” on page 39

■

“Attach the Slide-Rails” on page 43

Install AC Power Cables and Slide-Rails

Before you install the slide-rails into the rack, install right-angle AC power

cables into the left-side and right-side PDU electrical sockets.

Use the following 2-meter right-angle AC power cable for this procedure:

Installing the Storage Server Into a Rack

Summary of Contents for Exadata Storage Server X7-2 EF



























































































Search results

Summary of Contents for Exadata Storage Server X7-2 EF

Reviews:

Related manuals for Exadata Storage Server X7-2 EF

Brands by name

Popular brands

Oracle Exadata Storage Server X7-2 EF, Installation Manual

Search results

Summary of Contents for Exadata Storage Server X7-2 EF

Reviews:

Related manuals for Exadata Storage Server X7-2 EF

Brands by name

Popular brands