Oracle DE2-24 Customer Service Manual Download Page 160

Page: 160 / 312

Servicing the 7x20 Controller

TABLE 30

7420 Controller Dimensions

Dimension

Measurement

Dimension

Measurement

Height

13.3 cm/5.25 in

Depth

70.6 cm/27.8 in

Width

43.7 cm/17.19 in

Weight

16.36 kg/96 lbs

7420 Electrical Specifications

The following list shows the electrical specifications for 7420 controllers.

Note -

The power dissipation numbers listed are the maximum rated for the power supply and

are not a rating of the actual power consumption of the appliance.

Input

■

Nominal frequencies: 50/60Hz

■

AC operating range: 100-127 VAC for 2 CPUs and 200-240 VAC for 2 or 4 CPUs

■

Maximum current AC RMS: 12A @ 100 VAC / 12A @ 200 VAC

Power Dissipation

■

Max power consumption: 1800 W

■

Max heat output: 6143 BTU/hr

■

Volt-Ampere rating: 1837 VA @ 240 VAC, 0.98 P.F.

7420 Internal Boards

The 7420 controller chassis has the following boards installed. Field-replaceable units (FRUs)

should only be replaced by trained Oracle service technicians.

■

Motherboard:

The motherboard is a FRU and includes CPU modules, slots for eight

DIMM risers, memory control subsystems, and the service processor (SP) subsystem.

The SP subsystem controls the host power and monitors host system events (power and

environmental). The SP controller draws power from the host's 3.3V standby supply rail,

which is available whenever the system is receiving AC input power, even when the system

is turned off.

■

Power Distribution Board:

The power distribution board is a FRU and distributes main

12V power from the power supplies to the rest of the system. It is directly connected to

the Vertical PDB card, and to the motherboard through a bus bar and ribbon cable. It also

supports a top cover interlock ("kill") switch. In the storage controller, the power supplies

connect to the power supply backplane which connects to the power distribution board.

160

Oracle ZFS Storage Appliance Customer Service Manual • February 2016

Summary of Contents for DE2-24

























































































































































































































































































































Search results

Summary of Contents for DE2-24

Reviews:

Brands by name

Popular brands

Oracle DE2-24, Customer Service Manual

Search results

Summary of Contents for DE2-24

Reviews:

Brands by name

Popular brands