background image

KP100G 

 

Important Safety Descriptions 

Observe the following warnings and cautions when using the KP100G. 

‹

 Important user information:

 

 

WARNING 

 

 

 

CAUTION 

 

Injury due to electric shock, or fire, may possibly 
occur. Do not open the front cover or 
disassemble, modify, or repair. 

 

 

Burn injury will occur. Do not touch the upper part 
of the product cabinet during operation or 
immediately after stopping operation. 

 

Significant injury may possibly occur due to fire. 
Do not use the product in a flammable gas 
atmosphere (including flammable sprays such as 
pesticides). 

 

Fire will occur. Do not obstruct ventilation holes or 
place any objects within 20 cm of the ventilation 
holes. 

Fire will occur. Do not install near highly 
combustible items or heat sources (stoves, 
heaters, boilers, etc.). 

 

Injury due to electric shock or property damage due 
to burning may occasionally occur. Do not remove the 
MC connector, the AC output cover, RS-485 
protection cover, and the RS-232C protection cover. 
Do not unfasten of cable gland of AC output and RS-
485.  

 

Significant property damage may occasionally 
occur. Do not use the product at any country 
other than the designated one. 

 

 

Output power may be restricted due to ventilation 
obstruction. Clean the ventilation holes on top and 
bottom regularly. 

 

Injury or electric shock will occur. Read the 
manual and follow prior to using the product, 
and follow the instructions carefully. 

 

 

 

Electric shock or fire will occur. Have an installer 
from the store where you purchased the product, 
or an authorized service person, install, repair, 
modify, add on, move, or reinstall the product. 

 

 

 

 

Death may possibly result due to injury because 
the PV module operates at a high voltage. Do not 
remove the connector except for the instruction of 
the manual. 

 

 

 

 

Ask the store from which you purchased the 
product or an authorized person to dispose of it 
when it is no longer needed 

 

 

 

 

Precautions for Correct Use

 

Do not stand on the product and Data Logger or place any objects on it. 

Summary of Contents for KP100G























































Reviews: