H1 Multi-Function Digital Input Selections
H1-
Setting
Function
Description
Page
41
Reverse Run Command (2-Wire
sequence)
Open: Stop
Closed: Reverse run
94
61
External Search Command 1
Closed: Activates Current Detection Speed Search from the max. output
frequency (E1-04)
94
62
External Search Command 2
Closed: Activates Current Detection Speed Search from the frequency reference
94
67
Communications Test Mode
Tests the MEMOBUS/Modbus RS-422/485 interface.
95
No.
Name
Description
Range
Def.
Mode
Addr.
Hex
Pg.
H2: Multi-Function Digital Output MA-MB-MC
Use H2 parameters to assign functions to the multi-function digital output MA-MB-MC.
H2-01
Terminal MA, MB
and MC Function
Selection (relay)
Refer to H2 Multi-Function Digital Output Settings on page
176
for a description of setting values.
0 to 13D
E
O
40B
95
H2 Multi-Function Digital Output Settings
H2-01
Setting
Function
Description
Page
0
During Run
Closed: A Run command is active or voltage is output
95
1
Zero Speed
Closed: Output frequency is 0
95
2
Speed Agree 1
Closed: Output frequency equals the speed reference (plus or minus 2 Hz
hysteresis)
96
4
Frequency Detection 1
Closed: Output frequency is less than or equal to the value in L4-01 with 2 Hz
hysteresis
96
5
Frequency Detection 2
Closed: Output frequency is greater than the value in L4-01 with 2 Hz hysteresis
96
6
Drive Ready
Closed: Drive Ready. The drive is powered up, not in a fault state, and in the
Drive mode
97
7
DC Bus Undervoltage
Closed: DC bus voltage is below the Uv trip level
97
8
During Baseblock (N.O.)
Closed: There is no output voltage
97
B
Torque Detection 1 (N.O.)
Closed: Output current/torque exceeds the torque value set in parameter L6-02
for longer than the time set in parameter L6-03
97
E
Fault
Closed: Fault occurred (other than CPF00 and CPF01)
97
F
Not used
Set this value when the terminal is not used, or when using the terminal in the
pass-through mode
97
10
Minor Fault
Closed: An alarm is triggered
97
17
Torque Detection 1 (N.C.)
Open: When the output current exceeds the value set in parameter L6-02 for
more time than is set in parameter L6-03
97
1A
Reverse Direction
Closed: Drive is running in the reverse direction
98
1E
Restart Enabled
Closed: An automatic restart is performed
98
3C
LOCAL/REMOTE Status
Closed: LOCAL
Open: REMOTE
98
3D
Speed Search
Closed: Speed search is being executed
98
100 to 102;
104 to 108;
10B, 10E,
110, 117,
11A, 11E,
13C, 13D
H2 Parameter Functions Reversed
Output Switching of 0 to 13D
Reverse the output switching of the multi-function output functions. Set the last
two digits of 1
to reverse the output signal of that specific function
Examples:
Setting “108” reverses the output of “During baseblock”, which is setting value
08
Setting “13C” reverses the output of “LOCAL/REMOTE Status”, which is
setting “3C”
98
No.
Name
Description
Range
Def.
Mode
Addr.
Hex
Pg.
H3: Analog Input A1
Use H3 parameters to set the analog input terminal A1.
H3-01
Terminal A1
Signal Level
Selection
Sets the input level for terminal A1.
0: 0 to +10 V (lower limit)
1: 0 to +10 V (no lower limit)
2: 4 to 20 mA
3: 0 to 20 mA
0 to 3
0
O
410
98
H3-03
<22>
Terminal A1 Gain
Setting
Sets the level of the input value when 10 V (20 mA) is input at
terminal A1.
-999.9 to
999.9
100.0%
O
411
99
H3-04
<22>
Terminal A1 Bias
Setting
Sets the level of the input value when 0 V (0 or 4 mA) is input at
terminal A1.
-999.9 to
999.9
0.0%
O
412
99
H3-13 Analog Input Filter
Time Constant
Sets the primary delay filter time constant for terminal A1 or
potentiometer (optional). Used for noise filtering.
0.00 to 2.00 0.03 s
O
41B
101
<22> Parameter can be changed during run.
B.2 Parameter Table
176
SIEP C710606 33A OYMC AC Drive – J1000 User Manual