Omron G9SX-NS Brochure Download Page 18

Page: 18 / 28

D40A/G9SX-NS

Settin

Procedure

1. Cross Fault Detection (G9SX-NSA222-T0

)

Set the cross fault detection mode for safety inputs

y shorting Y1

to 24 V or leaving it open.
When cross fault detection is set to ON, short-circuit failures are
detected

etween safety inputs T11-T12 and T21-22. When a

cross fault is detected, the following will occur.
(1) The safety outputs and logical AND outputs lock out.
(2) The LED error indicator is lit.
(

) The error output (auxiliary output) turns ON.

2. Reset Mode (G9SX-NS202-

/NSA222-T0

)

Set the reset mode using feed

ack/reset input terminals T

1, T

and T

Auto reset mode is selected when terminal T

2 is shorted to 24 V

and manual reset mode is selected when terminal T

is shorted

to 24 V.

. Settin

ical AND Connection (G9SX-NS202-

NSA222-T0

)

When connecting two or more Non-contact Door Switch
Controllers

y logical AND connection, set the logical AND

connection preset switch on the Controller that is on the input side
(Unit B in the following diagram) to AND. The default setting of the
logical AND connection preset switch is set to OFF.

Note:

A setting error will occur and Unit B will lock out if the logical
AND setting switch on the Unit B is set to OFF.

4. Settin

the OFF-delay Time (G9SX-NSA222-T0

)

The OFF-delay preset time on G9SX-NSA222-T0

is set from

the OFF-delay time preset switch (1 each on the front and

ack of

the Unit).
Normal operation will only occur if

oth switches are identically set.

An error will occur if the switches are not identically set. The default
setting of the OFF-delay time preset switch is set to 0 s.

Refer to the following illustration for details on setting switch positions.

G9SX-NSA222-T0

Cross fault

detection

Wirin

OFF

Corresponds to
Safety Category 2.

Corresponds to
Safety Category

(Cross fault detecting
mode (for safety
inputs)).

T22

T21

T12

T11

+24 V

T22

T21

T12

T11

+24 V

T22

T21

T12

T11

+24 V

Auto reset mode

KM1

KM2

KM3

KM4

KM5

KM1

KM2

Reset
switch

KM3

KM4

KM5

T33

T32

T31

T33

T32

T31

Manual reset mode

Unit A

Unit B

T41

T42

AND

OFF

AND

OFF

Switch

Front

Back

Example 2: 0.8-second

Example 1: 0-second

OFF-DELAY

0.5

0.4

0.3

0.2

3.0

2.5

2.0

1.8

1.4

1.2

1.0

0.9

0.8

0.6

0.7

0.5

0.4

0.3

0.2

0.6

0.7

3.0

2.5

2.0

1.8

1.4

1.2

1.0

0.9

0.8

OFF-DELAY

Notch

Summary of Contents for G9SX-NS





























Search results

Summary of Contents for G9SX-NS

Reviews:

Related manuals for G9SX-NS

Brands by name

Popular brands

Omron G9SX-NS, Brochure

Search results

Summary of Contents for G9SX-NS

Reviews:

Related manuals for G9SX-NS

Brands by name

Popular brands