Omron G9SX-NS Brochure Download Page 7

Page: 7 / 28

D40A/G9SX-NS

Ratings (Non-contact Door Switch Controllers)

Power input

Power consumption of loads not included.

Inputs

*1.

Only applies to the G9SX-NSA222-T03-

. Refers to input other than that from the Non-contact Door Switch.

*2.

Provide a current equal to or higher than that of the minimum applicable load of the connected input control device.

Outputs

*1.

While safety outputs are in the ON state, the following signal sequence is output continuously for diagnosis.
When using the safety outputs as input signals to control devices (i.e. Programmable Controllers), consider the OFF pulse shown below.

*2.

The following derating is required when Units are mounted side-by-side.
G9SX-NS202-

/G9SX-NSA222-T03-

: 0.4 A max. load current

Expansion Unit

Item

Model

G9SX-NS202-

G9SX-NSA222-T03-

G9SX-EX-

Rated supply voltage

24 V DC

Operating voltage range

−

15% to 10% of rated supply voltage

Rated power consumption

3 W max.

4 W max.

2 W max.

Item

Model

G9SX-NS202-

/G9SX-NSA222-T03-

Safety input

Operating voltage: 20.4 VDC to 26.4 VDC, internal impedance: approx. 2.8 k

Feedback/reset input

Item

Model

G9SX-NS202-

/G9SX-NSA222-T03-

Instantaneous safety output

OFF-delayed safety output

P channel MOS FET transistor output
Load current: 0.8 A DC max.

Auxiliary output

PNP transistor output
Load current: 100 mA max.

OFF

360

s max.

Approx.100 ms

Item

Model

G9SX-EX-

Rated load

250 VAC, 3 A/30 VDC, 3 A (resistive load)

Rated carry current

3 A

Maximum switching voltage

250 VAC, 125 VDC

Summary of Contents for G9SX-NS





























Search results

Summary of Contents for G9SX-NS

Reviews:

Related manuals for G9SX-NS

Brands by name

Popular brands

Omron G9SX-NS, Brochure

Search results

Summary of Contents for G9SX-NS

Reviews:

Related manuals for G9SX-NS

Brands by name

Popular brands