background image

14 | 

P a g e

7.3

 

IF-006-1 Configuration Registers 

The IF-006-1 Configuration registers are stored in non-volatile memory. Changes to the serial configuration and 

Modbus address take affect at the completion of the Modbus transaction. 

MB 

Register  Type 

Access 

Description Status 

Reserved 

0xec00  u16[16]  -- 

Reserved, return Invalid Address 

I2C_Read Errors 

0xefd0 

u32 

Number of Read errors 

I2C_Write_Errors 

0xefd2 

u32 

Number of Write errors 

I2C_Read Retries 

0xefd4 

u32 

Number of Read Retries 

I2C_Write_Retries 

0xefd6 

u32 

Number of Write Retries 

I2C_Indirect_Retries 

0xefd8 

u32 

Number of Read Retries 

I2C_Read_Request 

0xefda 

u32 

Number of read requests 

I2C_Write_Request 

0xefdc 

u32 

Number of write requests 

Reserved 

0xefda 

-- 

-- 

Reserved, return Invalid Address 

PROBE_PROCESS_STATE 

0xefdf 

u16 

State variable- internal use only 

INTERFACE_ PASSWORD 

0xefe0 

u8[16]  RW* 

Read back as 0x01.. (blank) or 0x00 

(non blank) 

DEVICE_ID 

0xefe8 

u8[8] 

RW* 

Read only, but used as part of Boot 

load access mechanism 

FW_VERSION 

0xefec 

u32 

RW* 

Read only but used as part of Boot 

load access mechanism. Formatted as 

MM.mm.bb.cc

HW_VERSION 

0xefee 

u32 

Formatted as MM.mm.bb.cc 

DEVICE_TYPE 

0xeff0 

u16 

0xff05 == IF-006 

SYSTEM CONTROL 

0xeff1 

u16 

R/W 

System Control (See below) 

I2C_BASE_ADDRESS 

0xeff2 

u16 

R/W 

Defaults to 0x68. Sets base address of 

I2C device(s). 

I2C_SPEED 

0xeff3 

u16 

R/W 

I2C bus speed in kHz, ie 40 == 40 

kbit/second 

SERIAL_CONFIG 

0xeff4 

u16 

R/W 

See Serial Configuration Word 

MODBUS_ADDRESS 

0xeff5 

u16 

R/W 

Defaults to 1. Sets based address for 

Modbus transactions. Limited to 1 .. 

247. 

ADDRESS_RANGE 

0xeff6 

u16 

R/W 

Set to 0. No multi-device support 

SYSTEM_STATUS 

0xeff7 

u16 

System Status 

MANUFACTURED_DATE 

0xeff8 

u16 

Bit packed value with format 

YYYYYYY.MMMM.DDDDD 

USER_HOURS 

0xeff9 

u16 

R/W 

User settable counter, increments 

every 3600 seconds 

OPERATING_TIME 

0xeffa 

u32 

Total number of seconds of operation 

CORE_VERSION 

0xeffc 

U32 

-- 

Formatted as MM.mm.bb.cc 

INTERFACE_CONTROL 

0xeffe 

u16 

See Below 

GATEWAY_CONTROL 

0xefff 

u16 

Reserved 

Summary of Contents for IF-006









































Reviews: