5
ALARM3 DELAY: Set up Alarm 3 delay (refer to “Alarm Outputs” ) (display when OUT2 is set to
ALARM mode)
0
PV Color Change Function: Select the alarm to change PV display color. (refer to "Alarm Outputs")
OFF
2PID change temperature (display on 2PID control mode)
1.0
2PID reset temperature (display on 2PID control mode)
0.5
REMOTE TYPE: Set up Remote type (display when
is set to REMO mode)
(V0:0~5V; V1:1~5V; V10:0~10V; MA0:0~20mA; MA4:4~20mA)
MA4
Select auxiliary function 1
0
Select auxiliary function 2
0
COMMUNICATION WRITE: Enable/disable communication write-in
OFF
COMMUNICATION SELECT: Select ASCII or RTU format
ASCII
COMMUNICATION NO.: Set up communication address
1
BPS: Set up baudrate
9600
LENGTH: Set up data length
7
STOP: Set up stop bit
1
PARITY: Set up parity bit
Press
to return to input type setting
E
【
Regulation Mode
】
Parameter Settings:
Display
Description
Factory Setting
AT: Auto-tuning Switch
（
display when setting Ctrl = PID/FUZZY/2PID, TUNE = AT, R-S=RUN
）
Press
OFF
ST: SELF-TUNING Switch (display when setting Ctrl = PID, TUNE = ST)
OFF
PID NO.: Select the n
th
(n=0~5) PID. When set in AUTO, PID is auto-selected. (display when
setting Ctrl=PID)
0
~
PID SV NO.: Accordinig to the selection of PID No. (n=0~5), set SV value accordingly. It will allow
the system perform auto selection when it’s set to AUTO mode. (Display when Ctrl =
PID/FUZZY/2PID).
100
~
P : Proportional Setting (display when setting Ctrl = PID/FUZZY/2PID and TUNE = AT)
Set P value according to the selection of PID No. (n=0~5). When P is set to AUTO, the system will
select P value accordingly.
47.6
~
I: Integral Time Setting (display when Crtl=PID/FUZZY/2PID; this parameter is set automatically
when TUNE=AT.)
Set I value according to the selection of PID No. (n=0~5). When I is set to AUTO, the system will
select I value accordingly.
260
~
D: Deviation Time SEtting: (display when Crtl=PID/FUZZY/2PID; this parameter is set
automatically when TUNE=AT.)
Set D value according to the selection of PID No. (n=0~5). When D is set to AUTO, the system will
select D value accordingly.
41
~
I OFFSET: Integral deviation setting, when Integral is not 0. (display when Crtl=PID/FUZZY/2PID;
this parameter is set automatically when TUNE=AT.)
Set IOF value according to the selection of PID No. (n=0~5). When IOF is set to AUTO, the
system will select IOF value accordingly.
0
PD OFFSET: PD offset when Integral=0 to eliminate a consistent deviation.
0
Set up Fuzzy gain value (when Ctrl=FUZZY)
4
Set up Fuzzy Deadband (when Ctrl=FUZZY)
0
OUT1 HYSTERESIS: Adjust Output 1 hysteresis (when in ON/OFF control)
0
OUT2 HYSTERESIS: Adjust Output 2 hysteresis (when in ON/OFF control)
0
OUT1 HEAT: Heating control cycle for Output 1 ( when Ctrl= PID/FUZZY/MANUAL/2PID)
Output
selection:
C; V; S: 5sec.
R: 20sec.
OUT1 COOL: Cooling control cycle for Output 1 (when Ctrl= PID/FUZZY/MANUAL/2PID)
OUT2 HEAT: Heating control cycle for Output 2 ( when Ctrl= PID/FUZZY/MANUAL/2PID)
OUT2 COOL: Cooling control cycle for Output 2 (when Ctrl= PID/FUZZY/MANUAL/2PID)
COEF: Ratio of Output 1 against Output 2 (when Ctrl= PID/FUZZY/2PID and when in dual output
control)
1.00
DEAD: Set up deadband (when Ctrl is not set to MANUAL and when in dual output)
0
PV FILTER: Set up input filter factor of PV
1
PV RANGE: Set up input filter range of PV
1.00
