background image

8

Value + Compensation Value.   
For example: Measure Value=25.0; Compensation = 1.2. After applying to the Compensation equation PV=26.2. 

Linear  Compensation  Gain  (setting  range  =  -0.999~0.999).  Linear  Compensation  Gain  Calculation  equation:  PV  =

Measure Value* (1 + Gain/1.000) + Compensation.
For example: Measure Value=25.0; Gain= 0.100. After applying to the Gain calculation equation PV= 25.0 * (1 + 0.100 / 1.000) =
27.5

If temperature deviation is the same in every temperature, settting linear compensation value can solve deviation problem. If temperature 
deviation  varies  upon  different  temperatures,  calculate  the  linear  deviation  error  and  adjusts  the  temperature  by  setting  Gain  and 
Compensation value. 

 Applications of Analog Voltage & Current Input 

The input range of analog voltage and current are used as the uppler/lower limit of the controller’s voltage and current setting. When 
setting up the desire voltage or current, it must lies within the range of upper/lower limit. For example: If the range of analog input voltage 
is 0~5V, the upper limit setting will be 5000 and lower limit setting will be 0. If the decimal setting is set to 3 decimal place, a input voltage 
of 2.5V will displays as 2.500. The equation of Display Value = (Upper limit setting of controller– Lower limit setting of controller)*(Input 
voltage- Analog lower limit)/(Analog upper limit– analog lower limit) + Lower limit setting of controller.   

 Disable the Cold Junction Function 

The cold conjunction function of a thermocouple is set to ENABLE, but in some cases, we can set it to DISABLE.   

 

In Initial Setting Mode, 

  is used to set the first digit (Y) of Yxxx, (when Y=0, Enable; when Y=1, Disable). 

Analog Output Compensation 

When the output mode is set to analog current output (4~20mA) or linear voltage output (0~10V), user’s desire output value can be 
attained  by  using  compensation  function.  For  example,  the  analog  output  1  can  be  adjusted  in 

  and 

  parameters  in 

“Regulation  Mode”.  The  output  value  can  be  positive  or  negative  (+/-)  and  it  can  be  changed  by  pressing  the  Up/Down  key  on  the 
temperature controller. The scale of each pressing is an increase or decrease of 1uA and 1mV.   
For example: To change the current output range from 4~20mA to 3.9~20.5mA, set 

  to 500 (20.5-20=0.5mA; 0.5mA/1uA= 500). 

and set 

  to -100 (3.9-4=-0.1mA; -0.1mA/1uA=-100).   

To control the output manually: Set parameter

  to 

  in

Initial Setting Mode

.   

To set output to 0%: Set parameter

  to 

  or 

  to 

  in

Operation Mode

To adjust the lower limit of analog output: Input a desire value and check the meter to adjust the analog input value to desire value
(For example: 4~20 m A, adjusting analog value will be 20 m A). Set parameter 

  (Output 1) or 

  (Output 2) to your

desire value in 

Regulation Mode

.

To set output to 100%: Set parameter

  (Output 1) = 

  or   

  (Output 2) = 

  in 

Operation Mode

To adjust the lower limit of analog output: Input a desire value and adjust the analog input value to your desire value (For example:
4~20  m  A,  adjusting  analog  value  will  be  20  m  A).  Set 

  (Output  1)  or 

  (Output  2)  to  your  desire  value  in

Regulation Mode

.

 Retransmission and Compensation Adjusting 

When  the  input  value  changes,  the  retransmission  output  will  also  be  changed  correspondingly.  For  example:  If  retransmission  = 
4~20mA ; uppler/lower limit = 100.0 ~ 0. Wen the controller reads 0, it outputs 4mA; when the controller reads 100, it outputs 20mA. The 
value can also be a negative number to generate a negative slope. For negative slope, sets upper/lower limit = 0~100.0. In this case, 
when the controller reads 0, it outputs 20mA; when the controller reads 100, it outputs 4mA. Refer to the slope diagram below.   

Output = 

Negative Slope 

Output = 

Positive Slope 

(Figure 1: Propotional Output Diagram)

Summary of Contents for CND3 Series





























Reviews: