manualshive.com logo in svg

Olympus IPLEX NX IV9000N, Instructions Manual

Share
Download
Olympus IPLEX NX IV9000N Instructions Manual Download Page 17

9

IPLEX NX

 

· Do not allow the battery compartment to become deformed and 

never put any foreign object into it.

 

· Do not allow metal or water, or any other fluid to get into the battery 

compartment or onto the battery terminals.

If any foreign object enters the main unit, remove the battery and 

disconnect the AC adapter, and immediately contact Olympus.

 

· Do not remove the battery immediately if the instrument was used 

continuously for a long time.

The heat generated by the battery causes the risk of burn injury.

 

· Do not leave the battery in a location subject to moisture, water 

leakages or extremely high or low temperatures.

 

· Do not touch the battery terminals with your wet hands.

 

· If you plan not to use the instrument for a long time, remove the 

battery from the main unit and store it in a dry place.

Otherwise, the battery fluid may leak and the heat generation may result 

in a fire or injury.

 

· Keep the battery out of the reach of small children.

 

· If you are experiencing problems in inserting the battery, do not 

attempt to insert it forcibly.

Check the orientation of the battery and check the terminals for 

abnormalities. Attempting to insert the battery forcibly into the 

compartment may cause malfunction.

 

· If you are experiencing problems in removing the battery from the 

instrument, do not attempt to remove it forcibly.

Contact Olympus.

 

· Contact the airlines in advance if you plan to transport the battery by 

aircraft.

 

· When replacing the battery, do not repeat inserting or removing it 

rapidly.

Otherwise, the power may not be turned ON.

 

· When disposing of a battery, be sure to do so in accordance with all 

local laws, rules, and regulations.

Before disposing of batteries, check your local laws, rules, and 

regulations and follow them accordingly.

 

·

The contamination of battery electrodes with sweat or oil will cause the 
contact failure. If the battery is dirty, wipe it with a dry cloth before use.

 

·

Use the battery correctly. If the battery is used incorrectly, battery fluid 
leakage, heat generation or damage may result. Insert the battery in the 
correct orientation when replacing it.

 

·

Recommended temperature range for Li-ion battery operation.

 - Discharging (using main unit) : -10 °C to 40 °C

 - Charging 

:  0 °C to 45 °C

 - Storage 

: -20 °C to 60 °C

Using the battery under the temperature exceeding the temperature ranges 
described above will result in degradation of its performance and service life. 
Before storing the instrument, be sure to remove the battery from the main unit.

WARNING

CAUTION

NOTE

Summary of Contents for IPLEX NX IV9000N





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands