OLT SSGS812 Assembly Manual Download Page 1 | Manualshive

Page: 1 / 42

background image

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 1

Revision #1.12

February 8, 2022

Some of the safety and usage measures you may wish to consider include:

-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep
the snow off the roof(s).
-if the product is elevated, any structural and building code requirements are solely the customer's
responsibility, and should be abided by.
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.

Customer agrees to hold Outdoor Living Today Partnership and any Authorized Dealers
free of any liability for improper installation, maintenance and repair.

Thank you for purchasing
an 8x12 SunShed Greenhouse
Buidling from Outdoor Living
Today. Please take the time to
identify all the parts prior to
assembly.

Safety Points and Other Considerations
Our products are built for use based on
proper installation and normal residential
use, on level ground. Please follow the
instruction manual when building your
shed and retain the manual for future
maintenance purposes.

In the event of a missing or broken piece, simply call the Outdoor Living Today Customer
Support Line @ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our
commitment to you to courier replacement parts, free of charge, within 10 business days of
this notification. Replacement parts will not be provided free of charge after the 30 day grace
period.

Stock Code:

SSGS812-Metal

8x12 SunShed Greenhouse
Building with Metal Roof
Assembly Manual

1
2
3
...
»

Summary of Contents for SSGS812











































Reviews:

No comments

Related manuals for SSGS812

Brand: Eden Halls Greenhouses Pages: 24

Brand: AeroGarden Pages: 2

Hotbed G21 GZ11 XL

Brand: G21 Pages: 9

HOBBY GREENHOUSE 3m x 3m

Brand: Richel GROUP Pages: 16

Brand: Palram Pages: 16

Brand: Gardebruk Pages: 2

Brand: GrowLab Pages: 2

Brand: Growers SOLUTION Pages: 4

Brand: GrowSpan Pages: 27

Brand: Growing Spaces Pages: 12

Brand: Growhouse Pages: 22

4 TIER GREENHOUSE

Brand: ALDI Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands