OLT SSGS812 Assembly Manual Download Page 42 | Manualshive

Page: 42 / 42

background image

We hope your experience assembling your Sunshed has been both positive and rewarding.

We value your feedback and would like to hear back from you on how well we are doing in the
following areas:

1. Customer Service
2. On Time Shipping
3. Motor Freight Delivery
4. Quality of Materials
5. Assembly Manual
6. Overall Satisfaction.

Please call, write or email us at:

Toll Line: 1.888.658.1658 | Fax: 1.604.462.5333 | [email protected]

Canadian Address
9393 287th Street
Maple Ridge, British Columbia
Canada V2W 1L1

United States Address
P.O. Box 96
Sumas, Washington
USA 98295

Outdoor Living Today

Congratulations on Completing
your 8 x 12 Sunshed!

Note:

Our buildings are

shipped as an unfinished
product. If exposed to the
elements, the western red
cedar lumber will weather to
a silvery-gray color. If you
prefer to keep the cedar
lumber looking closer to the
original color, we suggest
that you treat the wood with
a good oil base wood stain.
You may also wish to paint
your new shed rather than
stain it. In both cases we
recommend that you
consult with a paint and
stain dealer in your area for
their recommendations.

The materials contained in this Assembly
Manual may be downloaded or copied
provided that

ALL

copies retain the copyright

and any other proprietary notices contained
on the materials. No material may be
modified, edited or taken out of context such
that its use creates a false or misleading
statement or impression as to the positions,
statements or actions.

Page 42

«
...
40
41
42

Summary of Contents for SSGS812











































Reviews:

No comments

Related manuals for SSGS812

Snap & Grow 8x8

Brand: Palram Pages: 43

Brand: ACD PRESTIGE Pages: 45

Brand: Growers SOLUTION Pages: 4

GreenHouse SP Series

Brand: PNI Pages: 54

Brand: Gutta Garden Pages: 40

Brand: ACF Greenhouses Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands