![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465126.webp)
%2-1 Paper input jam (1st tray)
[JAM error]
2-1
Paper input jam (1st tray)
Does a jam error occur when the power is turned on?
Yes
Is the paper at the inlet sensor lever?
Yes
Remove the paper.
No
Does the inlet sensor lever operate smoothly?
No
Replace the inlet sensor lever
Yes
Clean the inlet sensor on the Power/sensor board or replace the Power/sensor
board.
No
Does jam error occur after paper feeding?
Yes
Is the paper fed on the inlet sensor lever?
Yes
Does the inlet sensor lever operate smoothly?
No
Replace the inlet sensor lever.
Yes
Clean the inlet sensor on the Power/sensor board or replace the
Power/sensor board.
(See Fig. 2.3 Sensor Layout Diagram.)
No
Replace the hopping roller assembly or paper cassette assembly.
No
Is the hopping roller rotating?
Yes
Set the paper cassette properly.
No
Is the hopping motor rotating?
Yes
Replace the hopping roller gear (one way) or idle gear (HF)
A No
Are the cable and connector between the hopping motor and the Control board
connected properly? (see chapter 7.1.)
No
Connect each connector properly or replace the nylon connector cord (white: 9
pins).
Yes
Is the coil resistance (normal resistance: about 6.7 W) of the hopping motor normal?
No
Replace the hopping motor.
Yes
Replace the Control board.
Summary of Contents for OL1200ex
