Paper size
error
Paper of improper size was fed
from the tray.
tttttt: MANUAL, TRAY 1, TRAY
2 or ENVLOP
• Check the paper in the tray
or check to see if more than
one sheet of copy were fed
simultaneously.
• Open the cover, then close it
to perform recovery printing
and the error display is
released.
• If this error occurs
frequently, see chapter 6.5.2.
Paper size
error
A jam occurred during paper
feeding from the tray.
tttttt: MANUAL, TRAY 1, TRAY
2 or ENVLOP
• Check the paper in the
cassette. Open the cover, then
close it to perform recovery
printg and the error display is
released.
• If this error occurs
frequently, see chapter 6.5.2.
Jam errors
A jam occurred during paper
feeding from the tray.
tttttt: MANUAL, TRAY 1, TRAY
2 or ENVLOP
• Check the paper in the
cassette. Open the cover, then
close it to perform recovery
printg and the error display is
released.
• If this error occurs
frequently, see chapter 6.5.2.
Jam errors
A jam occurred during paper
feeding after finishing paper
hopping from the tray.
• Open the cover, remover the
paper, then close the cover.
When the cover is closed,
recovery printing is performed
and the error display is
released.
• If this error occurs
frequently, see chapter 6.5.2.
Daily status
Menu operation
Normal operation in menu
mode.
Daily status
The upper cover was opened.
• Close the cover to release
the error display.
• If the display does not
change after the cover is
closed, check for correct
operation of cover open/switch
and lever.
• Replace the Power Supply
board.
Controller
error
An error was detected by EEPROM
ID No. check.
• Press the RECOVER key on
the operator panel to reset the
EEPROM to the factory default
state and to release the error
display.
Summary of Contents for OL1200ex
