![background image](http://html1.mh-extra.com/html/okidata/ol1200ex/ol1200ex_service-manual_3678465056.webp)
%3.3.13 Separator F
3.3.13 Separator F
(1) Turn the AC power switch off. Unplug the AC power cord from the outlet.
(2) Remove the manual feed hopper Assy (see 3.3.4).
(3) Remove the side cover (R) (see 3.3.5).
(4) Remove the front feeder Assy (see 3.3.12 steps (1) to (3)). Make a diagram of wire locations
and routing.
(5) Remove two screws 1 and then remove the inner cover 2. At this time, the cover lock lever 3
and the torsion spring 4 are also removed. Note position of torsion spring.
(6) Remove two screws 5 and then remove square-shaped connector 6.
(7) Using great care, remove the connector of switch Assy 7 from square-shaped connector 6.
(8) Turn idle gear 8 in the direction of arrow A until front feeder plate 9 is elevated.
(9) Remove front feeder gear 10 and then remove two springs A. Be careful not to lose the springs.
(10) Remove four screws B and then remove paper supply guide C. (At this time, front feeder earth
plates D, G, and H are also removed.)
(11) Remove front feeder plate 9 by releasing the engagement at two parts 9A . Switch Assy 7 may
now be removed.
(12) Pull up separator E toward you and then release two mounting posts at 15A to remove the
separator. (At this time, two springs F are also removed. Be careful not to lose the springs.)
(13) Release two mounts on paper supply guide C and pull out switch Assy 7 upward.
During Re-assembly use great care: do not pinch, crimp, or cut wires to switch Assy 7.
Summary of Contents for OL1200ex
