manualshive.com logo in svg

Oki C5550, Maintenance Manual, Page: 221 / 313

Share
Download
Oki C5550 Maintenance Manual Download Page 221

Oki  Data  CONFIDENTIAL

44158801TH  Rev.2 

221 / 

Table 8-1-2  Service Call Error (6/7)

Message

Cause

Error Description

Solution

Service call 
220:Error

False setting of 
a record medium 
detected by a print 
statistics.

Take off the HDD or replaced?

Yes 

 
 

Reset original HDD.

Service call 
230:Error

RFID Reader not 
Installed

RFID read device error 
 
Is the error issued again?

Yes 

 

Yes 

 

Check the connection of 
the RFID R/W board. 
Replace the RFID R/W 
board. 
Replace the S2V PCB.

Service call 
231:Error

RFID Reader I/F 
Error

An interface error was detected with 
the RFID reader device.
01: communication error between 

the RFID reader and the engine 
PCB.

02: the transceiver circuit error of 

the RFID reader.

03: communication error between 

the RFID reader and the toner 
cartridge.

04: the toner cartridge detection 

error (more than 4).

01: Same as Error 230
02: Replace RFID R/W 

board.

03: Check the antenna 

cable connection.

04: Check to see if 

the quantity of toner 
cartridge is correct.

Service call 
250:Error

Secure File Erasing 
Error

An erasing error of an encrypted file 
was detected. 
Did the user agree to execute HDD 
ERASE?

Notify the user that Disk 
ERASE needs to be 
executed to erase the 
encrypted file, so that the 
HDD is restored to the 
original state as at the 
time of purchase.  ADMIN 
MENU HDD ERASE

Service call 
251:Error

Secure Disk 
Erasing Error

An error was detected during Disk 
ERASE.  
Can the error indication be 
reproduced?

 
 

Yes 

Turn the power off and on 
again. 
Replace the HDD. 

Power off/on 
901:Error 
902:Error

Short or open in 
belt thermistor 
detected.

Is belt thermistor cable setting 
proper? 
 
Does error reoccur?

No 

 

Yes 
Yes

Connect cable set 
properly again. 
Turn power ON again. 
Replace belt thermistor.

Power off/on 
903:Error 
904:Error

Abnormal 
temperature 
detected by belt 
thermistor (high-
temp or low temp.)

Is belt thermistor cable setting 
proper? 
 
Does error reoccur?

No 

 

Yes 
Yes

Connect cable set 
properly again. 
Turn power ON again. 
Replace belt thermistor 
and leave aside for 30 
min. Then turn power ON 
again.

Service call 
918:Error

Duplex FANO 
Alarm Detection

FAN error inside the Duplex.  
Is the error issued again when the 
power is turned on again?

Yes 

 

Yes

Check to see if the Duplex 
is properly installed. 
Check to see if the FAN is 
properly connected.  
Replace the FAN. 

Power off/on 
923:Error

Black Image 
Drum Lock Error

The black image drum (K-ID) does 
not rotate properly.  
Is the error message issued again 
when the power is turned on?

 
 

Yes 
Yes

Check to see if the K-ID is 
properly installed.  
Replace the K-ID. 
Replace the K-ID motor.

Summary of Contents for C5550


























































































































































































































































































































Reviews:

No comments