Oki C301 Maintenance Manual Download Page 94

Page: 94 / 218

44951501TH Rev.2

5-8

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

LEVEL0

Voltage display

during printing

Transfer (TR)
voltage (1) *1

Transfer (TR)
voltage (2) *1

Charge (CH)

voltage

Supply (SB)

voltage

Development

(DB) voltage

Environment level

After time-based

adjustment

Before time-

based adjustment

Time-based

correction value

Vtr3

*1: Pressing the CANCEL button switches between colors.

Toner sensor

status monitor

display

RFID internal noise

motor

Display of number

of times of noise

detection, K toner error

Display of number

of times of noise

detection, Y toner error

Display of number

of times of noise

detection, M toner

error

Display of number

of times of noise

detection, C toner

error

Motor control

evaluation function

Registration motor

constant-speed timer

value and ambient

temperature

Fuser motor constant-

speed timer value

and target fuser

temperature

Image drum motor

constant-speed timer

value

Belt motor constant-

speed timer value

held down (for two

seconds)

ONLINE held down (for two seconds)

Error detail

Appropriate display, such as error code display

Engine status display

Heater temperature

Ambient temperature and

humidity

Setting table

Transfer voltage

Transfer-off voltage and belt

temperature

Side thermistor

Waste toner

sensor

Waste toner

sensor status

monitor display

(1) Menu option switching

Holding down

or ONLINE or momentarily pressing or

switches

between the options in shaded areas ( XXXXX ). or is used to
switch between the options in non-shaded areas ( XXXXX ). Holding
down

restores the display that selects an option.

Self-diagnostic

mode layout (entire)

(1) Menu option switching

Only while displayed as shown in a shaded area (  XXXXX  ),
the level of the self-diagnostic mode can be switched.   or   is
used to switch to the option in a non-shaded area (  XXXXX  ).

LEVEL0- engine status

display

Engine status display

(Heater temperature)

(Ambient temperature and

humidity display)

Voltage display during printing

(TR, CH, DB or SB)

Toner sensor

Waste toner sensor

RFID internal noise motor

Error detail

LEVEL1-ENGINE DIAG MODE XX.XX

SWITCH SCAN

MOTOR & CLUTCH TEST

TEST PRINT

REG ADJUST TEST

DENS ADJ TEST

CONSUMABLE STATUS

PRINTER STATUS

FACTORY MODE SET

SENSOR SETTING

LED HEAD DATA

NVRAM PARAMETER

POWER ON

Normal operation mode

and ONLINE held

down in combination

(for three seconds)

, OK and

pressed in

combination

momentarily

No buttons pressed

and

held down until System Maintenance

menu appears. Then ENGINE DIAG MODE
selected and OK pressed.

Summary of Contents for C301



























































































































































































































Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands

Oki C301, Maintenance Manual

Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands