Oki C301 Maintenance Manual Download Page 146

Page: 146 / 218

44951501TH Rev.2

7-21

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING

Display

Causes

Error detail

Actions

SERVICE CALL

154:ERROR

Belt unit fuse-

cut error

Is the belt unit installed

properly?

Does the error occur again?

Yes

Re-install it.

Turn off and on

the printer.

Be sure of cable

connection, and

then replace the

CU/PU board.

SERVICE CALL

155:ERROR

Fuser unit

fuse-cut error

Is the fuser unit installed

properly?

Does the error occur again?

Yes

Clean the

connection

connector of the

fuser unit, and

then re-install the

fuser unit.

Turn off and on

the printer.

Be sure of cable

connection, and

then replace the

CU/PU board.

SERVICE CALL

160:ERROR

163:ERROR

Toner sensor

detection

error (160=Y,

161=M,

162=C,

163=K).

This error

does not

occur with

the printer in

the factory

shipped

configuration.

Is the toner cartridge

installed?

Is the toner slide shutter set?

Yes

Install the toner

cartridge.

Turn it to the fixed

position. Turn off

and on the printer.

Replace the toner

sensor assembly.

SERVICE CALL

167:ERROR

Thermistor

slope error

Does an error message

appear?

Does the error occur again?

Yes

Turn off and on

the printer.

Turn off and on

the printer after

leaving it for 30

minutes.

Display

Causes

Error detail

Actions

SERVICE CALL

168:ERROR (Note)

Compensation

thermistor

error

Does an error message

appear?

Does the error occur again?

Yes

Turn off and on

the printer.

Turn off and on

the printer after

leaving it for 30

minutes.

SERVICE CALL

170:ERROR

171:ERROR (Note)

A fuser

thermistor

short or open

circuit was

detected.

Does the error occur again?

Yes

Turn off and on

the printer.

Replace the fuser

unit.

SERVICE CALL

172:ERROR

173:ERROR

A fuser

thermistor

temperature

error (high

or low

temperature)

was detected.

Does the error occur again?

Yes

Turn off and on

the printer.

Replace the fuser

unit.

Replace the low-

voltage power

supply, and then

replace the CU/

PU board when

the error occurs

again.

SERVICE CALL

174:ERROR

A backup

thermistor

shot circuit

was detected

(high

temperature)

Does the error occur again?

Yes

Turn off and on

the printer.

Replace the fuser

unit.

SERVICE CALL

175:ERROR (Note)

A backup

thermistor

open

circuit was

detected (low

temperature)

Does the error occur again?

Yes

Turn off and on

the printer.

Replace the fuser

unit.

Summary of Contents for C301



























































































































































































































Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands

Oki C301, Maintenance Manual

Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands