manualshive.com logo in svg

Oki C301, Maintenance Manual

The Oki C301 User Manual is available for free download on manualshive.com, providing clear instructions and helpful guidelines for optimal use of this advanced printer. Seamlessly access the comprehensive manual to enhance your printing experience and maximize the potential of your Oki C301.

Share
Download
background image

44951501TH  Rev.2 

7-16

Oki  Data  CONFIDENTIAL

7. TROUBLESHOOTING

Operator panel display

Online 

lamp

Atten-

tion 

lamp

Description

Code 

nnnnnn

CHECK TONER 

CARTRIDGE

%ERRCODE%:%COLOR% 

TONER SENSOR ERROR

Off

Blink

Indicates a toner sensor detected an 

error.

    Error 540 : Y

    Error 541 : M

    Error 542 : C

    Error 543 : K

Error

540

541

542

543

OPEN TOP COVER

%ERRCODE%:PAPER 

SIZE ERROR

Off

Blink

Notifies that, from the tray, paper of an 

improper size was fed. Check the paper 

in the tray, or the printer for a multi feed. 

Cover opening and closing makes the 

printer to perform recovery printing to 

proceed.

Error 

400

CHECK MP TRAY

%ERRCODE%:PAPER 

JAM

Off

Blink

Indicates that, during feeding paper from 

the MP tray, a paper jam occurred.

    Error 390 : MPTray

Error

390

OPEN TOP COVER

%ERRCODE%:PAPER 

JAM

Off

Blink

Indicates that, during feeding paper from 

the tray, a paper jam occurred.

    Error 391 : Tray1

    Error 392 : Tray2

Error

391

392

OPEN TOP COVER

%ERRCODE%:PAPER 

JAM

Off

Blink

Indicates that a paper jam occurred in a 

paper path.

    Error 380 : Feed

Error

380

OPEN TOP COVER

%ERRCODE%:PAPER 

JAM

Off

Blink

Indicates that a paper jam occurred in a 

paper path.

    Error 381 : Transport

    Error 382 : Exit

    Error 385 : Around Fuser Unit

    Error 389 : Printing Page Lost

Error

381

382

385

389

OPEN TOP COVER

%ERRCODE%:FACE UP 

STACKER ERROR

Off

Blink

Indicates that, during printing, the face-

up stacker is operated and the printer 

pauses, causing error.

Error 

409

Operator panel display

Online 

lamp

Atten-

tion 

lamp

Description

Code 

nnnnnn

CHECK UNDER BELT

%ERRCODE%:PAPER 

JAM

Off

Blink

Indicates a paper jam occurred near the 

duplex unit.

    Error 370 : Duplex Reversal

    Error 371 : Duplex Input

Error

370

371

CHECK UNDER BELT

%ERRCODE%:PAPER 

JAM

Off

Blink

Indicates a paper jam occurred near the 

duplex unit.

    Error 372 : Duplex Misfeed

Error

372

REPLACE IMAGE DRUM 

UNIT

353:DRUM UNIT LIFE

Off

Blink

Notifies the end of the life of an image 

drum (an alarm). Cover opening and 

closing puts the printer into a warning 

state.

Error 

353

REPLACE IMAGE DRUM 

UNIT

563:DRUM UNIT LIFE

Off

Blink

Notifies the end of the life of an image 

drum (an alarm). This display is provided 

until the image drum is replaced.

Error 

563

REPLACE FUSER

%ERRCODE%:FUSER 

LIFE

Off

Blink

Notifies the end of the life of the fuser. 

This is an error that indicates a counter 

shows the end of the fuser life is 

reached. The printer stops printing with 

the error. Cover opening and closing 

puts the printer into a warning state.

Error 

354

REPLACE BELT

%ERRCODE%:BELT LIFE

Off

Blink

Notifies the end of the life of the transfer 

belt. This is an error that indicates a 

counter shows the end of the belt life is 

reached. The printer stops printing with 

the error. Cover opening and closing 

puts the printer into a warning state.

Error 

355

REPLACE BELT

%ERRCODE%:BELT LIFE

Off

Blink

Indicates the printer is full of waste toner. 

Cover opening and closing puts the 

printer into a warning state only once, 

and then after printing 500 pages, the 

printer has an error.

Error 

356

Summary of Contents for C301



























































































































































































































Reviews:

No comments

Related manuals for C301

Magicard Pronto Getting Started Manual preview
Pronto
Brand: Magicard Pages: 26
QMS 3260 Operation preview
3260
Brand: QMS Pages: 194
J&Maya JMB4 User Manual preview
JMB4
Brand: J&Maya Pages: 21
Star SM-S301 Hardware Manual preview
SM-S301
Brand: Star Pages: 24
ICT GP83 Service Manual preview
GP83
Brand: ICT Pages: 34
Keithley Model 750 Instruction Manual preview
Model 750
Brand: Keithley Pages: 97
iDPRT SP410 User Manual preview
SP410
Brand: iDPRT Pages: 41
Epson EPL-N1200 Reference Manual preview
EPL-N1200
Brand: Epson Pages: 256
Oce CS 5090 User Manual preview
CS 5090
Brand: Oce Pages: 199
Dascom DP-80 Quick Start Manual preview
DP-80
Brand: Dascom Pages: 2
Samsung MultiXpress C9201NA Brochure & Specs preview
MultiXpress C9201NA
Brand: Samsung Pages: 8
Samsung MultiXpress C8380ND Specifications preview
MultiXpress C8380ND
Brand: Samsung Pages: 6
Samsung MultiXpress 6322DN Information Sheet preview
MultiXpress 6322DN
Brand: Samsung Pages: 6
Samsung MultiXpress 6345N Compatibility Manual preview
MultiXpress 6345N
Brand: Samsung Pages: 10
Samsung MultiXpress K430 SERIES User Manual preview
MultiXpress K430 SERIES
Brand: Samsung Pages: 34
Samsung MSYS 5200 User Manual preview
MSYS 5200
Brand: Samsung Pages: 137
Samsung ML-3561N Series Service Manual preview
ML-3561N Series
Brand: Samsung Pages: 156
Samsung MSYS 5200 Service Manual preview
MSYS 5200
Brand: Samsung Pages: 210

Brands by name

Popular brands

Load more brands