Oki C301 Maintenance Manual Download Page 147

Page: 147 / 218

44951501TH Rev.2

7-22

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING

Display

Causes

Error detail

Actions

SERVICE CALL

176:ERROR

177:ERROR

A backup

thermistor

temperature

error (high

or low

temperature)

was detected.

Does the error occur again?

Yes

Turn off and on

the printer.

Replace the fuser

unit.

Replace the low-

voltage power

supply.

SERVICE CALL

182:ERROR

Option unit

interface error

Does the error occur again?

Yes

Turn off and on

the printer.

Be sure of

connector

connection.

Replace the

option unit.

POWER OFF/ON

190:ERROR

System

memory

overflow

Does the error occur again?

Yes

Turn off and on

the printer.

Replace the CU/

PU unit.

SERVICE CALL

200:ERROR

202:ERROR

PU firmware

download

error

An error occurred in re-writing

the PU firmware.

Turn off and on

the printer, and

then re-download

it (In general use

of the printer, this

re-writing is not

performed and

this error does not

occur).

POWER OFF/ON

209:DOWNLOAD

ERROR

Custom

Media

Type table

downloading

failure

Custom Media Type table

downloading failed.

Turn off and on

the printer, and

then re-download

it (In general use

of the printer, this

downloading is

not performed

and this error

does not occur).

Display

Causes

Error detail

Actions

POWER OFF/ON

203:ERROR

204:ERROR

207:ERROR

208:ERROR

213:ERROR

214:ERROR

F0C:ERROR

FFE:ERROR

FFF:ERROR

CU program

error (203

to 214 do

not occur in

general use

of the printer)

Invalid processing was

performed with a CU program.

Replace the CU/

PU board.

SERVICE CALL

231:ERROR

TAG interface

error

A TAG interface error was

detected.

01: A circuit error.

03: TAG communication error.

Be sure the toner

cartridges and

the image drums

are properly set.

Replace the toner

cartridges. When

the error occurs

again after the

image drums

are re-installed,

be sure of the

cable connection

from the CU/PU

board to the toner

sensor board.

POWER OFF/ON

250:ERROR

SD card error

SERVICE CALL

251:ERROR

SD card

erasure error

POWER OFF/ON

252:ERROR

255:ERROR

SD card

security error

POWER OFF/ON

256:ERROR

257:ERROR

SD card error

Summary of Contents for C301



























































































































































































































Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands

Oki C301, Maintenance Manual

Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands