Oki C301 Maintenance Manual Download Page 129

Page: 129 / 218

44951501TH Rev.2

7-4

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING

Panel display ( identifies

that no display is provided)

On-

line

lamp

Atten-

tion

lamp

Detail

CHECKING FILE

SYSTEM

Off

Indicates that file system is being checked.

Process Check of File System is valid to start

from "FILE SYS MAINTE2"-"CHECK FILE SYS" of

Admin Menu. (only C531)

ERASING SD CARD

Off

Indicates that the SD Card is being erased.

Erase process of the SD Card is valid to start from

"FILE SYS MAINTE2"-"SD CARD ERASE" of

ADMIN MENU. (only C531)

CHECKING SECTORS

nnn%

Off

Indicates that a sector of SD Card is being

checked.

Check process of the sector is valid to start from

"FILE SYS MAINTE2"-"CHK ALL SECTORS" of

Admin Menu.

nnn

Percentage of checked capacity . (only C531)

PROGRAM UPDATA

MODE

Off

Indicates the printer is in a mode dedicated to update

the NIC program (the controller firmware). By turning

on the printer while holding down the ONLINE button,

the printer is put into the mode.

WAIT A MOMENT DATA

RECEIVE

Off

Blink Indicates update NIC program data is being received.

WAIT A MOMENT

DATA RECEIVED OK

Off

Indicates reception of update NIC program data is

complete.

CHECK DATA

REC DATA ERROR

<n>

Off

Indicates that the printer has an error during

reception processing of update NIC program data.

<n>

1: A size error.

2: A checksum error.

3: A printer model number error.

4: A module interface version error.

5: A FAT version error.

WAIT A MOMENT

DATA WRITING

Off

Blink Indicates update NIC program data is being written.

Panel display ( identifies

that no display is provided)

On-

line

lamp

Atten-

tion

lamp

Detail

POWER OFF/ON

DATA WRITTEN OK

Off

Indicates writing of update NIC program data is

complete.

CHECK DATA

DATA WRITE ERROR

<n>

Off

Indicates that the printer has an error during writing

of update NIC program data.

<n>

1: A memory allocation error.

2: A download file error.

3: An error in obtaining available device memory.

4: An error of insufficient available device memory

5: A file writing error.

6: A CU firmware mismatch error.

LOADER VERSION

XX.XX

Off

Indicates that the PU firmware is running in

the Loader mode. The CU firmware sends this

message at power-on of the printer. This message

may occur in user environments, requiring

maintenance by maintenance personnel (like

service calls)

COMMUNICATION

ERROR

Off

Indicates communication with the PU firmware

failed. This message may occur in user

environments, requiring maintenance by

maintenance personnel (like service calls).

STATUS MODE

Off

Indicates that the printer started in the permanent

online mode. Even when having an error after

starting in the mode and going online (into a Ready

state), the printer processes data (jobs) sent from

the outside (a host), indicating an error or warning

on the panel. Turning on the printer while using an

OK, Back and Down button combination puts the

printer into the mode. The button combination is

transparent to users, and this state occurs in no

user environments.

Summary of Contents for C301



























































































































































































































Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands

Oki C301, Maintenance Manual

Search results

Summary of Contents for C301

Reviews:

Related manuals for C301

Brands by name

Popular brands