Oki C301 Maintenance Manual Download Page 136 | Manualshive

Page: 136 / 218

background image

44951501TH Rev.2

7-11

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING

Panel display ( identi-

fies that no display is

provided)

On-

line

lamp

Atten-

tion

lamp

Detail

Solution

PRESS ONLINE SW
COLOR RESTRICTED.
MONO PRINTED

PRESS ONLINE SW
COLOR RESTRICTED.

JOB REJECTED

PRESS ONLINE SW
PRINT RESTRICTED.

JOB REJECTED

Varies

On

Notifies the user that, as the user was
not authorized to print a job, the job
was canceled (in connection with job
accounting). This display is provided
until the ONLINE button is pressed.

Set a print job

accounting
user ID in the
printer driver.
Check a user
ID and the
setting for the
user ID with the
job accounting
administrator
when the user
ID is already
set in the driver.

PRESS ONLINE SW
LOG BUFFER FULL.

JOB REJECTED

Varies

On

Notifies the user that the log buffer
was full and a job was canceled (in
connection with job accounting). This
display is provided until the ONLINE
button is pressed.

Execute Acquire

a Log

on

the print job
accounting
server PC.

PRESS ONLINE SW
EXPIRED SECURE

JOB

Varies

On

Indicates a job of which storage period
for secure printing was exceeded was
canceled. (only C531)

-

PRESS ONLINE SW

INVALID SECURE

DATA

Varies

On

Indicates that, as data damage was
detected through completeness
checking in secure printing, a job was
deleted. (only C531)

-

Panel display ( identi-

fies that no display is

provided)

On-

line

lamp

Atten-

tion

lamp

Detail

Solution

PRESS ONLINE SW
DISK USE FAILED
%FS_ERR%

Varies

On

Indicates a file system error other than
the above file system-related status
states occurred. Processing that does
not use the file system is available.
%FS_ERR%
=0

GENERAL ERROR

=1

VOLUME NOT AVAILABLE

=3

FILE NOT FOUND

=4

NO FREE FILE DESCRIPTORS

=5

INVALID NUMBER OF BYTES

=6

FILE ALREADY EXISTS

=7

ILLEGAL NAME

=8

CANT DEL ROOT-

=9

NOT FILE

=10

NOT DIRECTORY

=11

NOT SAME VOLUME

=12

READ ONLY

=13

ROOT DIR FULL

=14

DIR NOT EMPTY

=15

BAD DISK

=16

NO LABL

=17

INVALID PARAMETER

=18

NO CONTIG SPACE

=19

CANTCHANGE ROOT

=20

FD OBSOLETE

=21

DELETED

=22

NO BLOCK DEVICE

=23

BAD SEEK

=24

INTERNAL ERROR

=25

WRITE ONLY

Replace the
SD memory
card only for
use of printing,
such as secure
printing.

PRESS ONLINE SW
INVALID DATA

*C531/C331/C321

PRESS ONLINE SW
INVALID DATA OR
TIMEOUT

*C511/301

Varies Varies Prompts pressing the ONLINE button

to clear this warning as the printer
received invalid data. This display is
provided at reception of an unsupported
PDL command.

Press the
ONLINE button.

«
...
134
135
136
137
138
...
»

Summary of Contents for C301



























































































































































































































Reviews:

No comments

Related manuals for C301

imagePROGRAF iPF8300S

Brand: Canon Pages: 52

Brand: Canon Pages: 2

Accel-a-Writer 8300

Brand: Xante Pages: 12

3635MFP - Phaser B/W Laser

Brand: Xerox Pages: 16

Brand: OEC Pages: 28

Brand: Parkside Pages: 104

Brand: Xerox Pages: 2

ECOSYS P6230cdn

Brand: Kyocera Pages: 258

Brand: U-Line Pages: 30

Brand: SPRT Pages: 15

Brand: Olivetti Pages: 558

Brand: Star Micronics Pages: 127

Brand: Oce Pages: 76

Brand: Canon Pages: 22

Pixma iP1600 Pixma iP1200

Brand: Canon Pages: 24

PIXMA G4610 Series

Brand: Canon Pages: 20

Brand: Canon Pages: 60

Brand: Canon Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands