manualshive.com logo in svg

OHAUS Adventurer Pro Grain, Instruction Manual

Share
Download
OHAUS Adventurer Pro Grain Instruction Manual Download Page 33

           EN-31

Adventurer Pro Grain Test Scale

5. TECHNICAL DATA

Ambient conditions
The technical data are valid under the following ambient conditions:

• Ambient temperature: 10 °C to 30 °C
• Relative humidity: 15 % to 80 % at 31 °C non-condensing, decreasing linearly to 50

% at 40 °C

• Height above sea level:  Up to 4000 m

Operability is assured at ambient temperatures between 5 and 40 °C

Power

• AC adapter - To national standard as per list in Section 4.6.  Scale power input

6-14.5 VAC, 50/60Hz 4VA or 7-20VDC, 4W

Materials

• Housing base: plastic (ABS/PC)
• Top Housing: plastic (ABS/PC)
• Platform: 18/10 stainless steel

Protection

• Protected against dust and water
• Pollution degree: 2
• Installation category: Class II
• EMC: see declaration of conformity

Overall Dimensions

C

B

A

5.1 Outline Drawing

  

A

  B

              C

OVERALL          OVERALL           OVERALL
HEIGHT

  WIDTH

     DEPTH

 8.5 cm

22 cm

       30 cm

 3.3 in.

8.7 in.

    11.8 in.

8 page 31 to 35.pmd

7/27/2006, 3:11 PM

31

Summary of Contents for Adventurer Pro Grain







































Reviews:

No comments

Brands by name

Popular brands

Load more brands