manualshive.com logo in svg

OHAUS Adventurer Pro Grain, Instruction Manual

Share
Download
OHAUS Adventurer Pro Grain Instruction Manual Download Page 29

           EN-27

Adventurer Pro Grain Test Scale

Symptom

Possible Cause

Remedy

Scale will not turn on

• AC power not connected

• Connect AC adapter

Scale does not display

• Improper calibration

• Perform

accurately

• Unstable environment

calibration

• Move scale to a

suitable location

Cannot calibrate the scale

• Calibration menu locked

• Turn Calibration menu

lock off

• LFT set to on

• Turn LFT off

• Unstable weight reading

• Eliminate vibration and

drafts.

Cannot change Menu settings

• Submenu locked

• Unlock submenu

• LFT set to on

• Turn LFT off

Error 7.0

• Unstable weight reading

• Eliminate vibration and

when defining the

drafts.

reference weight.

Error 8.1

• Weight reading exceeds

• Clear pan.

 Power On Zero limit.

Error 8.2

• Weight reading below

• Put pan on scale.

Power On Zero limit.

Error 8.3

• Weight reading exceeds

• Clear pan.

overload limit.

Error 8.4

• Weight reading below

• Put pan on

underload limit.

scale.

Error  9.0

• Internal fault.

• Return scale for service.

4. MAINTENANCE
4.1 Calibration

Periodically verify calibration by placing an accurate weight on the scale and if calibration is
required, refer to section 3.8.1.

4.2 Cleaning

If cleaning is required, use a soft cloth dampened with water and a mild detergent.  Do not allow
liquids to enter the scale.  Do not use harsh chemicals to clean the scale, as the finish may be
damaged.

4.3 Troubleshooting

The following table lists common problems, possible causes and remedies.  If the problem persists,
contact Ohaus or your authorized Ohaus dealer.

7 page 19 to 30.pmd

7/27/2006, 3:11 PM

27

Summary of Contents for Adventurer Pro Grain







































Reviews:

No comments

Brands by name

Popular brands

Load more brands