Odyssey ODY-5 Owner'S Manual Download

Page: 15 / 36

FIG. 47

Begin routing the

Pec Dec Cable (#39)

through the Nylon

Pulley 4 1/2 Rd. (#64-Labeled S), then up and over the Nylon Pulley 4 1/2
Rd. (#64-Labeled T) located on the

Closed-End Double Pulley Bracket

(#26)

, then down and under the Nylon Pulley 4 1/2 Rd. (#64-Labeled U).

Finally, route the end of the

Pec Dec Cable (#39)

to the

Right Pec Dec

Arm (#6)

. Use the same hardware and procedure that was used for the

Left Pec Dec Arm (#7)

as described in

Fig. 46

Note

: Refer to the Cable Mapping Diagram on page 23 for further

detailed illustration of the

Pec Dec Cable (#39)

routing.

FIG. 48

Locate the

Tension Cable (#40)

and attach it to the pulley

bracket located on the

Base Frame (#2)

. Secure the cable into place

using one Hex Head Cap Screw 3/8-16 X 1 3/4 (#93), two Flat Washers
SAE 3/8” (#71), two Nylon Spacers 3/8 X 3/8 (#104) and one Nylon Insert
Jam Lock Nut 3/8-16 (#82). Refer to

Fig. B

on page 24 for further

clarification of this hardware assembly.

Note

: Refer to the Cable Mapping Diagram on page 24 for further

detailed illustration of the

Tension Cable (#40)

routing.

FIG. 49

Route the

Tension Cable (#40)

up and over the Nylon Pulley

4 1/2 Rd. (#64-Labeled V) located on the

Closed-End Pulley Bracket

(#26)

Note

: Refer to the Cable Mapping Diagram on page 24 for further

detailed illustration of the

Tension Cable (#40)

routing.

FIG. 50

Continue to route the

Tension Cable (#40)

down and under

the Nylon Pulley 4 1/2 Rd. (#64-Labeled W), as shown above.

Note

: Refer to the Cable Mapping Diagram on page 24 for further

detailed illustration of the

Tension Cable (#40)

routing.

ODY-5 Odyssey Home Gym

Owner’s Manual: Assembly Instructions

Summary of Contents for ODY-5





































Search results

Summary of Contents for ODY-5

Reviews:

Related manuals for ODY-5

Brands by name

Popular brands

Odyssey ODY-5, Owner'S Manual

Search results

Summary of Contents for ODY-5

Reviews:

Related manuals for ODY-5

Brands by name

Popular brands