Odyssey ODY-5 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 36

Odyssey ODY-5 Owner'S Manual Download Page 20

ODY-5 CABLE ADJUSTMENT DIAGRAM

Fully Fasten

: Proceed to Fully Fasten all these hardware

assemblies .

FULLY FASTEN

Cable Adjustment for:

Adjustable Pulley Bracket (#36)

1. Loosen the bottom Regular Hex Nut (#80)
2. Adjust the top Nylon Insert Lock (#79) to give the

cable proper tension.

3. Re-tighten the bottom Regular Hex Nut (#80) to

complete the cable adjustment.

Cable Adjustment for:

Adjustable Stopper (#26)

1. Loosen the Regular Hex Nut (#80)
2. Twist the

Adjustable Stopper (#26)

to left or right

until you have achieved proper cable tension.

3. Re-tighten the Regular Hex Nut (#80) to complete

the cable adjustment.

Note

: Be sure that the

Closed-End Double

Pulley Bracket (#26)

is always resting on the

Adjustable Stopper (#33)

.

Cable Adjustment for:

Adjustable Stopper (#26)

1. Loosen the bottom Regular Hex Nut (#80)
2. Twist the

Adjustable Stopper (#26)

to left or right

until you have achieved proper cable tension.

3. Re-tighten the bottom Regular Hex Nut (#80) to

complete the cable adjustment.

Note

: Be sure that the

Closed-End Double

Pulley Bracket (#26)

is always resting on the

Adjustable Stopper (#33).

Cable Adjustment for:

Adjustable Double Pulley Plates

(#27)

1. Remove the hardware from the Nylon Pulley 4

1/2 Rd. (#64) located at one of the four holes on
the plates.

2. By interchanging the Nylon Pulley 4 1/2 Rd. (#64)

to the next adjustment hole will make a one inch
cable adjustment.

3. Re-tighten the hardware for Nylon Pulley 4 1/2

Rd. (#64) to complete the cable adjustment.

The Diagram below depicts the location of the cable adjustments on each
work station. It is imperative that you maintain the cables’ proper adjust-
ment to ensure a safe and smooth operation.

Cables should be inspected and adjusted periodically to avoid any
slack in the cables which would, consequently, prevent any damage
to the equipment or personal injury.

19

ODY-5 Odyssey Home Gym

«
...
18
19
20
21
22
...
»

Summary of Contents for ODY-5





































Reviews:

No comments