Oce PlotWave 300 User Manual Download Page 23

Page: 23 / 340

The Océ PlotWave 300 hardware

The components of the printer (front)

Illustration

Component - function table

Description / Function

Component

Remove this cover if you want to move the
printer.

lower left front cover

Door at the front, used for error recovery.

lower front cover

To manually feed cut-sheets up to 36"
width.

media bypass

Compartment for toner refill.

toner compartment

Only available in printer-only version.

printer top cover

Delivery tray for the printed sheets.

top delivery tray

USB connector to use a USB mass storage
device to print from or to scan to, if a
scanner is available.

USB flash drive interface

Chapter 2 - Get to know the printing system

The components of the printer (front)

Summary of Contents for PlotWave 300





















































































































































































































































































































































Search results

Summary of Contents for PlotWave 300

Reviews:

Related manuals for PlotWave 300

Brands by name

Popular brands

Oce PlotWave 300, User Manual

Search results

Summary of Contents for PlotWave 300

Reviews:

Related manuals for PlotWave 300

Brands by name

Popular brands