background image

 

NOTE CMDS ACCEPTED 

(Direct Dimmer Access Off) 

 
CMD 

   NOTE 

NUMBER NOTE 

VALUE 

 

 ACTION    

 
Note 

on 

   32 

47 

  1 

127 

  Causes 

lighting 

control 

          channel 

16 

to 

fade 

to 

          assigned 

intensity 

level. 

 
Note 

on 

   32 

47 

  0 

  Note-on 

of 

is 

ignored. 

 
Note off  

 

 

32 - 47   

 

0 - 127   

 

Note off is ignored. 

 
Note on  

 

 

64 - 79   

 

1 - 127   

 

Flash Scene. Causes lighting 

          control 

channel 

16 

to 

come 

          instantly 

to 

full 

intensity. 

          Has 

precedence 

over 

all 

other 

 

 

 

 

 

 

 

 

 

 

lighting levels. 

Note 

on 

   64 

79 

  0 

  Causes 

lighting 

control 

or 

         channel 

32 

turned 

on 

by 

Note off  

 

 

64 - 79   

 

0 - 127   

 

previous Flash scene to return 

 

 

 

 

 

 

 

 

 

 

to previous intensity level 

 

 

 

 

 

 

 

 

 

 

instantly. 

 

(Direct Dimmer Access on) 

 
Note 

on 

   0 

63 

  1 

127 

  Instantly 

causes 

available 

          dimmer 

channel 

64 

to 

          come 

to 

assigned 

level. 

          The 

greatest 

level 

has 

          precedence 

when 

used 

together 

 

 

 

 

 

 

 

 

 

 

with console controls. 

 
Note 

on 

   0 

63 

  0 

  May 

cause 

dimmer 

channel 

or 

         previously 

set 

by 

note 

on 

Note off  

 

 

0 - 127   

 

0 - 127   

 

instantly return to original 
console control level depending  
on Dimmer Access mode. 

 

PROGRAM CHANGES ACCEPTED 

 
PROGRAM 

NUMBER 

 ACTION          

 
0 - 15 

Activates memory scene of current page at current fade rate control or CTL CHG 
#1 setting. 

 
64 - 79   

 

 

Changes current page number 1 - 16 

 
80 

   Deactivates 

Chase. 

81 - 84 

Activates normal chase number 1 - 4 at current chase rate control or CTL CHG #2 
setting. 

 
97 

 

 

 

Activates memory scene black - out. 

 

Summary of Contents for NCM 6200




















Reviews: