Nortel Meridian M1250 User Manual Download Page 82

Page: 82 / 168

• • • • 76 • • • •

Basic call processing

Recovery on Misoperation of Attendant Console

The Recovery on Misoperation of Attendant Console feature provides a safeguard on the

Meridian 1 to prevent calls from being inadvertently disconnected.

The following lists the console functions in the event of accidental misoperation:

Pressing the Release Key or Loop Key is ignored when:

•

Extending a call to a vacant number

•

Extending to a partially dialed number

•

Extending a Network blocked call

•

Extending a call to a restricted station or trunk

•

Extending to a station in the Do Not Disturb (DND) mode

•

Extending to a station in the Make Set Busy (MSB) mode

•

Extending to a maintenance busy station

•

Extending to a station in a line lockout state

•

Illegal call extension due to trunk barring

•

Extending to a busy station with no Camp-on/Call Waiting

•

Illegal call extension due to Trunk-to-Trunk Conference Restriction

•

Illegal release from a conference connection

Autohold on loop key - the active loop is automatically placed on hold if the
attendant presses another loop key prior to extending the active call.

Does not allow the disconnection of a single excluded party or conference call.
If one of the parties on a loop is excluded, the operation of the corresponding
Release Source Key or Release Destination Key is ignored.

Summary of Contents for Meridian M1250








































































































































































Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands

Nortel Meridian M1250, User Manual

Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands