manualshive.com logo in svg

Nortel Meridian M1250, User Manual

Share
Download
Nortel Meridian M1250 User Manual Download Page 123

• • • • 117 • • • •

Convenience features

Storing a Speed Call number

If your console is designated a Speed Call controller, you can store a number for Speed Call and use the 
Speed Call codes. Also use this number-storing procedure to change a number stored against a Speed 
Call code.

1

When all lpk indicators 
are off, press S. call.

The S. call indicator 
flashes.

2

Dial the one-, two-, or 
three-digit code to be 
associated with the 
phone number.

3

To see if a number is 
already associated with 
the dialed code, press 
disp. src.

The current speed-call list 
entry (if any) is displayed.

4

Dial the number to be 
stored. Press * after 
every trunk access code 
to ensure a pause for dial 
tone.

5

Press S. call again.

The S. call indicator goes 
off; the access code and 
phone number you dialed 
are stored together for 
speed-calling.

Summary of Contents for Meridian M1250









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands