Nortel Meridian M1250 User Manual Download Page 49

Page: 49 / 168

• • • • 43 • • • •

Basic call processing

Extending a call to a busy extension (with Camp-on)

After you have answered a call, you can extend it to the extension the caller requests.

Note:

If a camped call is not answered within the set time, it is returned to you.

Dial the requested
extension.

The excl. src. indicator

goes on during dialing.

The D indicator flashes;

the extension is busy.

If you do not hear a busy

signal and the caller

wishes to wait, you can
camp the call onto th

busy extension by
pressing RLS.

If you do hear a busy

signal after dialing the
requested extension,
either a call is already

camped onto that

extension, or Camp-on is

not allowed on that
extension.

The RLS indicator goes
on; you are free to process

other calls.

If you do hear a busy

signal after dialing the
requested extension and
the caller wishes to call

back later, press RLS

dest., and then RLS to
end your connection in

the call.

The D indicator goes off

;

the called extension is

released from the console.
The RLS indicator goes
on; you are free to process

other calls.

Summary of Contents for Meridian M1250








































































































































































Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands

Nortel Meridian M1250, User Manual

Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands