Nortel Meridian M1250 User Manual Download Page 121

Page: 121 / 168

• • • • 115 • • • •

Convenience features

Speaking privately (Splitting)

Splitting allows you to talk to a called party without the caller hearing, or to talk to a caller without the
called party hearing.

A caller requests an
extension. To exclude
the caller from the
connection, press excl.
src.

The excl. src. indicator
goes on.

Dial the requested
extension. The called
party answers. Talk
privately with the called
party.

You hear ringing but the
caller does not. The D
indicator flashes slowly.
Upon answer, ringing
stops and the LCD
indicator goes on steadily.

To exclude the called
party from the
connection, press excl.
dest. You and the caller
are reconnected. Talk
privately.

The excl. src. indicator
goes off. The excl. dest.
indicator goes on.

To connect yourself, the
caller, and the called
party, press the lpk key.

The excl. dest. indicator
goes off.

To end your connection
in the call, press RLS.

The RLS indicator goes
on; you are free to
process other calls.

Summary of Contents for Meridian M1250








































































































































































Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands

Nortel Meridian M1250, User Manual

Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands