Nortel Meridian M1250 User Manual Download Page 168

Page: 168 / 168

• • • • 162 • • • •

Supervisory features

Supervisory assistance

Despite the fact that your console may be in supervisory mode, another attendant can call you for
assistance or transfer a call to you.

Note:

If an attendant tries to transfer a call to you while your console is in supervisory mode, the call

waiting indicator goes on. To answer the call you must leave the Position Busy state.

You receive a call from
an attendant while your
console is in supervisory
mode.

You hear a tone. The S
indicator flashes. The
inter pos. C. ICI indicator
goes on.

Press the lpk key beside
the flashing S indicator.

The tone stops and the lpk
and S indicators go on
steadily; you are
connected to the call.

Summary of Contents for Meridian M1250








































































































































































Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands

Nortel Meridian M1250, User Manual

Search results

Summary of Contents for Meridian M1250

Reviews:

Brands by name

Popular brands