manualshive.com logo in svg

Nortel Meridian M1250, User Manual

Share
Download
Nortel Meridian M1250 User Manual Download Page 111

• • • • 105 • • • •

Convenience features

Turning Enhanced Night Service on and off

Enhanced Night Service permits incoming calls that would normally be directed to the console to be 
routed to a preselected destination when the console is unattended. Your console may be equipped with 
either regular Night Service or enhanced Night Service, but not both. Ask your System Administrator 
which one the console is equipped with.

When all consoles but one are in Position Busy mode and the attendant at the only active console presses 

, the system is automatically placed in Night Service.

1

To activate enhanced 
Night Service for a single 

console, press 

. 

Unplug the handset or 
headset.

The current Night Service 
option number is 
displayed.

2

To cancel enhanced 
Night Service for a single 
console, plug in the 
handset or headset.

3

To activate enhanced 
Night Service for 
multiple consoles, press 

SHIFT plus

 at any 

console. Unplug all 
handsets and headsets.

The current Night Service 
option number is 
displayed.

4

To cancel enhanced 
Night Service for 
multiple consoles, plug 
at least one handset or 
headset.

Summary of Contents for Meridian M1250









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands