4
2. OWNER INFORMATION
ABOUT YOUR CENTRAL
FURNACE SYSTEM
NORDYNE has been involved in the design of products for the
manufactured home industry since the first manufactured
home or trailer was built.
NORDYNE originated the sealed combustion system, which
separates the furnace combustion system from the living
area of the home, now a standard for the manufactured home
industry.
NORDYNE engineers developed the first central heating
system and the first central air conditioner for manufactured
homes.
NORDYNE is dedicated to bringing to its customers the finest
heating and cooling comfort possible. NORDYNE constantly
seeks to further refine its products to continuously provide
exceptional comfort.
Follow the instructions in this booklet carefully and this
appliance will provide many years of superior performance.
If you wish to cool your home automatically with a central air
conditioning system investigate the excellent NORDYNE
cooling systems available from your heating and cooling
contractor. These systems are designed to work best with
your NORDYNE furnace and have been carefully engineered
to deliver optimum performance when mated with NORDYNE
manufactured home furnaces.
NORDYNE also offers water heaters, fireplaces and ventilating
systems specifically designed for manufactured housing
applications. Check with your manufactured home retailer,
your heating and cooling contractor or your distributor for
information. Write directly to the factory (PO Box 46911, St.
Louis, MO 63146) if you are not able to locate a source for
NORDYNE manufactured housing products in your area.
3. MANUFACTURER WARRANTY,
OWNER’S RESPONSIBILITIES
It is the sole responsibility of the homeowner to make certain
the gas furnace has been correctly set up and converted to
the proper fuel (L.P. gas or Natural gas) and adjusted to
operate properly. All gas furnaces are manufactured for
Natural gas and must be field converted when using L.P. gas.
A warranty certificate with full details is included with these
instructions. However, NORDYNE will not be responsible for
any costs found necessary to correct problems due to
improper setup, improper installation, furnace adjustments,
improper operating procedure on the part of the user, etc.
Some specific examples of service calls which cannot be
included in warranty payments are:
1. Converting the furnace to use another type of gas.
2. Repairing duct work in the home found to be faulty.
3. Correcting wiring problems in the electrical circuit supplying
the furnace.
4. Resetting circuit breakers, blown fuses or other switches.
5. Correcting problems due to improper gas supply pressure
to the furnace.
6. Providing instructional training on how to light and operate
the furnace.
7. Furnace problems caused by installation of an air
conditioner, heat pump or other air comfort devices.
8. Adding a Roof Jack extension because of unusual wind
and/or snow conditions.
9. Revising installation of the furnace flue assembly (Roof
Jack).
10. Adjusting or calibrating of thermostat.
11. Any construction debris which falls into flue system.
Carefully review these responsibilities with your manufactured
housing dealer, service company or gas supplier so there will
be no misunderstanding at a later time.
4. INSTALLATION STANDARDS
Installer shall be familiar with and comply with all codes and
regulations applicable to the installation of these heating
appliances and related equipment. In lieu of local codes, the
installation shall be in accordance with the current provisions
of one or more of the following standards.
a. Federal Manufactured Home Constructions & Safety
Standard (H.U.D. Title 24, Part 3280.707[a][2])
b. American National Standard (ANSI-119.2/NFPA-
501C) for all recreational vehicle installations.
c. American National Standard (ANSI-Z223.1/NFPA-54)
and/or CAN/CGA B149 for all gas-fired furnace models.
d. American National Standard (ANSI-Z95.1/NFPA-31)
and/or CSA B139 for all oil-fired furnace models.
e. American National Standard (ANSI-C1/NFPA-70) and/
or CSA 22.1 Canadian Electric Code Part 1 for all
electrical field wiring.
f.
Units have been investigated under standards UL
307A & B, ANZI 21.47a — CAN/2.3a - 1995, and CSA
B140.10.
CAUTION:
•
Never attempt to alter or modify this furnace or
any of its components.
•
Never attempt to repair damaged or inoperable
components. Such action could cause unsafe
operation, explosion, fire and/or asphyxiation.
•
If a malfunction has occurred, or if you feel that
the furnace is not operating as it should, contact
a qualified service agency or gas utility for
assistance.
!
