background image

3

Table 2. M1 Furnace Specifications

NOTICE TO INSTALLER

Installer is advised to follow carefully all instructions and
warnings in this manual to insure maximum performance,
safety, and operating efficiency of these appliances. Improper
installation may create hazardous conditions, and will void
the appliance warranty.

1. SPECIFICATIONS

GENERAL DESCRIPTION

M1 Series gas and oil furnaces are  listed direct vent (sealed
combustion), downflow heating   appliances for manufactured
(mobile) homes, recreational vehicles, and for use in residential/
modular/commercial construction. The furnace must be located
so that venting can be properly achieved.

“A” cabinet models may be installed with Optional Coil Cabinet
Model #911969 for air conditioning.

“B” cabinet models are factory equipped with a built-in coil cavity.

Multi-speed blower assemblies as shown in Table 3 have
been certified for field installation in M1 Series furnaces. An air
conditioner can be easily field installed with M1GH Series
furnaces if used in conjunction with certified 2-wire relay box,
p/n 903092A or 4/5 wire relay box 902898A.

Electrical Supply - 120 volts, 60HZ, 1 Ph.

Thermostat Circuit - 24 volts, 60HZ, 30 vac

Fuse or Breaker - 15 amps

Normal Anticipator Setting - 0.4

Temperature Rise - 45° to 75°F

Manifold Pressure - Natural Gas: 3.5” w.c.    LP Gas: 10” w.c.

High Altitude - See Table 11. For Canadian High Altitude (2,000’ to 4,500’), reduce the gas manifold pressure
to 3.0” W.C. for natural gas and to 8” W.C. for LP gas.
*Blower capacity only - needs relay box for AC

Table 3. Field Installation Blower Assemblies

A/C Capacity

Blower Wheel

Motor-Hp

Ton

903412

10 x 8

1/3

2, 2½ & 3

903413

11 x 8

1/2

2, 2½, 3 & 4

903414

10 x 8

3/4

2, 2½, 3, 4 & 5

Part No.

Blower / Motor Assembly

Furnace

Input

Output

Orifice No

E.S.P.

Pilot

Ignitor

Comb.

Motor

A/C Ready

Model No

MBtu/h

MBtu/h

Nat.

LP

In WC

Burner

Direct

Blower

Hp

Tons

M1GH 056

56

45

29

45

0.2

x

1/8

2*

M1GB 056

56

45

29

45

0.3

x

1/3

3

M1GC 056

56

45

29

45

0.3

x

1/2

4

M1GD 056

56

45

29

45

0.3

x

3/4

5

M1GH 070

70

57

24

42

0.3

x

1/5

2½*

M1GB 070

70

57

24

42

0.3

x

1/3

3

M1GC 070

70

57

24

42

0.3

x

1/2

4

M1GD 070

70

57

24

42

0.3

x

3/4

5

M1GH 077

77

60

21

40

0.3

x

x

1/4

3*

M1GB 077

77

60

21

40

0.3

x

x

1/4

3

M1GC 077

77

60

21

40

0.3

x

x

1/2

4

M1GD 077

77

60

21

40

0.3

x

x

3/4

5

M1GH 090

90

70

17

36

0.3

x

x

1/4

3*

M1GB 090

90

70

17

36

0.3

x

x

1/4

3

M1GC 090

90

70

17

36

0.3

x

x

1/2

4

M1GD 090

90

70

17

36

0.3

x

x

3/4

5

M1MA 056

56

46

29

45

0.2

x

x

1/8

2

M1MB 056

56

46

29

45

0.3

x

x

1/3

3

M1MC 056

56

46

29

45

0.3

x

x

1/2

4

M1MD 056

56

46

29

45

0.3

x

x

3/4

5

M1MA 070

70

57

24

42

0.3

x

x

1/5

M1MB 070

70

57

24

42

0.3

x

x

1/3

3

M1MC 070

70

57

24

42

0.3

x

x

1/2

4

M1MD 070

70

57

24

42

0.3

x

x

3/4

5

M1MB 077

77

62

21

40

0.3

x

x

1/4

3

M1MC 077

77

62

21

40

0.3

x

x

1/2

4

M1MD 077

77

62

21

40

0.3

x

x

3/4

5

M1MB 090

90

72

17

36

0.3

x

x

1/4

3

M1MC 090

90

72

17

36

0.3

x

x

1/2

4

M1MD 090

90

72

17

36

0.3

x

x

3/4

5

M1BA 066

66

53

26

43

0.24

x

x

1/5

M1BC 066

66

53

26

43

0.3

x

x

1/2

4

M1BB 086

86

68

18

37

0.3

x

x

1/4

3

M1BC 086

86

68

18

37

0.3

x

x

1/2

4

M1SA 066

66

54

.50 Gph  

0.24

x

Burner Model

1/5

M1SC 066

66

54

.50 Gph 

0.3

x

AF-10 Nozzle

1/2

4

M1SB 086

86

71

.65 Gph 

0.3

x

Spray Angle

1/4

3

M1SC 086

86

71

.65 Gph 

0.3

x

80° A

1/2

4

Summary of Contents for M1GB 056





























Reviews: