background image

VARIABLE SPEED ELECTRIC FURNACE 

INSTALLATION INSTRUCTIONS

VARIABLE SPEED ELECTRIC FURNACE SAFETY

Table of Contents

VARIABLE SPEED ELECTRIC FURNACE SAFETY.....................1

INSTALLATION REQUIREMENTS ................................................2

Tools and Parts ............................................................................2
Location Requirements ................................................................2
Installation Configurations ...........................................................3
Electrical Requirements ...............................................................4
Duct Work Requirements.............................................................4

INSTALLATION INSTRUCTIONS ..................................................4

Inspect Shipment .........................................................................4
Install Duct Work ..........................................................................5

Filter Specifications ......................................................................5
Make Electrical Connections .......................................................5
Complete Installation..................................................................10

SEQUENCE OF OPERATION ......................................................12

ELECTRIC FURNACE MAINTENANCE ......................................13

ASSISTANCE OR SERVICE .........................................................13

Accessories ................................................................................13

WARRANTY ..................................................................................14

065682600

You can be killed or seriously injured if you don't
immediately follow instructions.

You can be killed or seriously injured if you don't
follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:

Summary of Contents for WEFV08S-1A

















Reviews: