background image

W415-1066 / C / 06.22.12

1

INSTALLER:  LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER:  SAVE THESE INSTRUCTIONS

INSTALLATION AND 

OPERATING INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonheatingandcooling.com • [email protected]

SAFETY INFORMATION

!

WARNING

If the information in these instructions are not followed 
exactly, a fi re or explosion may result causing property 
damage, personal injury or death.
Please read entire manual before you install and use your 
heater.

-  This heater can be very hot when burning.
-   Combustible materials such as fi rewood, wet clothing, etc. 

placed too close can catch fi re.

-   Children and pets must be kept from touching the heater when 

it is hot.

-   The chimney must be sound and free of cracks. Before 

installing this unit, contact the local building or fi re or other 
authority having jurisdiction and follow their guidelines.

-  Operate only with the doors tightly closed.
-  Do not use an elevated grate or otherwise raise the fi re.
-   This heater is designed to burn natural wood only. Higher 

effi ciencies and lower emissions generally result when 
burning air dried seasoned hardwoods, as compared to 
softwoods or to green or freshly cut hardwoods.

-   Do not start a fi re with chemicals or fl uids such as gasoline, 

engine oil, etc.

-   Do not burn treated wood, coal, charcoal, coloured paper, 

cardboard, solvents or garbage.

-   Do not let the heater become hot enough for any part to glow 

red.

HOT GLASS WILL 

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

!

WARNING

$10.00

HYBRID 100

HMF100

MULTI-FUEL FURNACE

CERTIFIED UNDER U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) JULY 1992 40 C.F.R. PART 60 AND THE OREGON DEPARTMENT OF ENVIRONMENTAL 

QUALITY (D.E.Q.) PARTICULATE EMISSION STANDARDS BY E.E.M.C.  CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: UL 391-2010, 

CSA-B366.1-11, UL1995-2005/CSA C22.2 NO.236-05.

RPT# 415-S-10-2

Summary of Contents for HYBRID 100

























































































Reviews: